Newco cb-2 参考指南

COMMERCIAL BARISTA DEC 2001 

•

= Power Save (Standby) - In this mode the tank temperature will be maintained at approximately 170 degrees when the set 

time has been reached.  Brew 1 light will flash about once every 10 seconds to indicate unit is in power save mode. 

•

= Power Down - In this mode the tank heater element will be disabled when the set time has been reached.  Brew 2 light 

will flash about once every 10 seconds to indicate unit is in power down mode. 

 

 

•

=

Depress and hold Cancel button until display lights up (Approx. 10 seconds). 

•

=

You are now in the Program Mode. Functions to be programmed appear in the order in which they are shown in the following table. 

•

=

Use the Cancel button to cycle through the functions to find the one you wish to change. 

•

=

Use the BREW 1 button to lower the displayed value and the BREW 2 button to raise the value. Press Cancel to store the changed value and 
advance to next function. 

•

=

If the Brewer detects no activity for approx. 60 seconds it will exit the Program Mode, except as noted below. 

 

1A 

Brew 1 time  

OFF, 30 ounces – 255 ounces 

BREW 1 

1b 

Brew 2 time  

OFF, 30 ounces – 255 ounces 

BREW 2 

2a 

Dual volume- brew1 
Double dump feature 

ON or OFF 

Water filtering Brew 1 

2b 

Dual volume- brew2 
Double dump feature 

ON or OFF 

Water filtering Brew 2 

3 

Visa-brew time     

OFF, 30  seconds – 2 ½ minutes 

BREW 1 and BREW 2 (both flashing) 

4 

Water Temperature   1 

170 

°

F – 205 

°

F  

SERVICE 

5 

Auto Arm 

ON or OFF 

HEATING, (flashing) 

6A 

Pre-infusion 1 mode 

ON or OFF 

BREW 1, (pulsing), COFFEE MONITOR 

6b 

Pre-infusion 2 mode 

ON or OFF 

BREW 2, (pulsing), COFFEE MONITOR 

7 

Pulse brew mode 

ON or OFF 

BREW 1 and BREW 2 (pulsing) 

7A 

Pulse brew 1 time    2 

0 seconds – 60 seconds 

BREW 1 (pulsing) 

7b 

Pulse brew 2 time    3 

0 seconds – 60 seconds 

BREW 2 (pulsing) 

8A 

Audible alert mode 

ON or OFF 

None 

8b 

Audible alert no. of beeps 

OFF, 1 – 9 

None 

9 

Coffee freshness monitor 

10 minutes – 2 hours 

COFFEE MONITOR 

10A 

Filtering flow rate 

OFF, 0.25 – 1.00 gal. / min 

WATER FILTERING 

10b 

Filter capacity     4 

OFF, 0.50 – 2.50 gal. X 100 

WATER FILTERING, (flashing) 

11 

Number of Brews 

Quantity, Clr 

BREW 1 and BREW 2 

13A Power 

mode 

Normal, Power Save, Power Down 

None (Displayed  P: n, P: s and P: d respectively) 

13b Power shutdown time    5 30 minutes – 4 hours None 

End 

None   6 

N/A None 

 
1 

Brewer will remain in this sequence indefinitely until CANCEL button is pressed.  Heating icon will track heater operation. 

2 

Hidden if pulse brew mode is OFF or brew 1 time is OFF. 

3 

Hidden if pulse brew mode is OFF or brew 2 time is OFF. 

4 

Hidden if filter flow rate is OFF. 

5 

Hidden when power save mode is normal. 

6 

Program mode will time out in 15 seconds at end of programming sequence.  

 

 
The following table explains the error messages which may be encountered on the brewer.  The error messages may be cleared 
by going into the program mode, using the brew buttons to display “Clr” and then pressing the cancel button. 
 

Er1 

Fill run error 

The fill solenoid has either run for more than six minutes on the initial tank fill 
or 3 minutes in normal operation. 

Er2 

Heater run error 

The tank heater has run for more than 30 consecutive minutes. 

Er3 

Shorted probe 

Short in the thermistor circuit. 

Er4 

Open probe 

Break in the thermistor circuit. 

Ful 

Filter limit reached 

The selected filtering capacity of the filter has been reached