Leviton ae6ma 安装指导

inputs

Gold Plated RCA jacks with adjustable gain

input impedance

50k Ohms

outputs

5 way gold plated binding posts

RMS continuous

50 Watts (40 Watts per channel 20Hz to 20kHz

@ <0.2% THD all channels driven into 8 ohms)

6 - 8 Ohms nominal

speaker impedance
frequency response  10 Hz - 40 kHz +/- 1dB (1W)
S/n ratio

over 105 dB A weighted (50 Watts)

tHD distortion

less than 0.1% 20 Hz to 20 kHz

iMD distortion

less than 0.01% 60 Hz 7 kHz 4:1 (SMPTE)

trigger control

12 VDC 35mA on 3.5mm mono jack

Dimensions

17" x 3.5" x 11.5" (432 x 89 x 292mm)

fan noise

quiet 28 dBA

power

750 Watts at 117 VAC or 230VAC

Weight

22 lbs (10 kg)

•  automatic protection circuitry – Each amplifier channel is individually and fully protected against low impedance, overheating, overloading, over

voltage and under voltage. The protection circuitry automatically restores the sound once the affected amplifier channel returns to the safe operating
area.

•  individual input gain adjustment – Each channel features an input gain adjustment to adjust the channel for volume, gain, and speaker sensitivity

variations.

•  external power on/off – The amplifier can be turned off and on by external controllers. To activate external power “on”, apply a 12VDC current to the

trigger jack using a compatible power supply. As long as the 12VDC is applied, the amplifier will remain on. The amplifier power switch should be in the
“off” position for external power control.

•  Link feature – The Link button is normally set to the “in” position to give all six stereo inputs individual sources. When the Link button is set to the

“out” position, that input Left/Right is internally linked or cascaded to the source connected to input #1. Any of the five inputs (2 through 6) can be linked
individually in any combination to the #1 input. When all inputs are linked to input #1 the input impedance is about 8500 Ohms.

 note: When linked, unused RCA inputs can be used as outputs to other amplifiers.
•  cooling fan – The AE6MA features a thermostatically controlled internal fan to help to avoid overheating and keeping all channels within the safe

operating area so that the likelihood of the protection circuitry being activated is reduced. The fan also helps maximize energy efficiency.

TO BE INSTALLED AND/OR USED IN ACCORDANCE WITH APPROPRIATE ELECTRICAL CODES AND REGULATIONS.

IF YOU ARE NOT SURE ABOUT ANY PART OF THESE INSTRUCTIONS, CONSULT A QUALIFIED ELECTRICIAN.

Never listen to sound that is distorted. If distorted sound is heard, turn the volume down immediately or speaker and/or amplifier damage

could occur that is not covered by the warranty.

The AE6MA contains no user serviceable parts. Do not attempt to open or repair the AE6MA.

user adjustments and Service: There are no user adjustments on the AE6MA. Your installer may make certain gain level adjustments on the rear panel.
1. The most important consideration when installing the AE6MA is cooling, since the amplifier packs a lot of audio power into a small-sized chassis. When

installing the amplifier in an equipment stack, it should be the top component. Make sure to leave at least 3-5 inches (76.19mm-127mm) of space above
the amplifier to allow for adequate cooling.

2. Never operate the AE6MA on its side, as it will impair the unit’s cooling and void the warranty.
3. Connect the AE6MA RCA inputs to the source component outputs using good quality RCA cables. Connect each channel individually, unless using the

Link feature.

4. Connect the AE6MA speaker outputs to speakers using good quality speaker wire. It is recommended that 18 AWG speaker wire be used for runs up

to 50 feet (15 m). For runs from 50-150 feet (15-45 m), 16AWG speaker wire should be used. And for runs over 150 feet (45 m), 14 AWG speaker wire
should be used. Make sure the wire used is correctly rated for installation inside walls, ceilings, or floors. Check local codes for complete information.

50 Watts RMS per Channel

Cat. No. AE6MA

Leviton warrants to the original consumer purchaser and not for
the  benefit  of  anyone  else  that  this  product  at  the  time  of  its
sale by Leviton is free of defects in materials and workmanship
under normal and proper use for two years from the purchase
date. Leviton’s only obligation is to correct such defects by repair
or replacement, at its option, if within such two year period the
product  is  returned  prepaid,  with  proof  of  purchase  date,  and
a  description  of  the  problem  to  Leviton  Manufacturing  co., 
inc., att:  Quality assurance  Department,  59-25  Little  neck 
parkway,  Little  neck,  new  York  11362-2591.  This  warranty
excludes  and  there  is  disclaimed  liability  for  labor  for  removal
of  this  product  or  reinstallation.  This  warranty  is  void  if  this
product  is  installed  improperly  or  in  an  improper  environment,
overloaded, misused, opened, abused, or altered in any manner,
or  is  not  used  under  normal  operating  conditions  or  not  in
accordance with any labels or instructions. there are no other 
or implied warranties of any kind, including merchantability 
and  fitness  for  a  particular  purpose,  but  if  any  implied
warranty is required by the applicable jurisdiction, the duration of
any such implied warranty, including merchantability and fitness
for a particular purpose, is limited to two years. Leviton is not 
liable  for  incidental,  indirect,  special,  or  consequential 
damages,  including  without  limitation,  damage  to,  or 
loss  of  use  of,  any  equipment,  lost  sales  or  profits  or 
delay  or  failure  to  perform  this  warranty  obligation.  The
remedies  provided  herein  are  the  exclusive  remedies  under
this  warranty,  whether  based  on  contract,  tort  or  otherwise.

DI-000-AE6MA-00B

DI-000-AE6MA-00B

Outputs

Outputs

Outputs

AC120V

8 amps

Inputs use RCA connectors

Outputs use speaker binding posts

Inputs

Gain

Link-Out

1R

1L

L

R

1

2

2L 2R

1L+

1R+

1L–

1R–

2L–

2R–

2L+

2R+

3L+

3R+

3L–

3R–

4L–

4R–

4L+

4R+

5L+

5R+

5L–

5R–

6L–

6R–

6L+

6R+

Inputs

Gain

Link-Out

3R

3L

L

R

3

4

4L 4R

Link-Out

Link (out position)

cascades channel 1

to channels 2-6

Inputs

Gain

Link-Out

12V trigger

5R

5L

L

R

5

6

6L 6R

Link-Out