Whirlpool DU1055XTV 安装指导

Wire stripper

Small 
tubing cutter

Electric drill 
with 1/2", 3/4” 
and 1-1/2" hole 
saw bits

Pliers

UL listed or CSA 
approved twist-on 
wire connectors*

Small level

Utility knife

Phillips 
screwdriver

5/16” and 1/4” 
nut drivers or 
hex sockets

Measuring tape 
or ruler

10” adjustable wrench 
that opens to 
1-1.8” (2.9 cm)

Flat-blade 
screwdriver

5/8” open-end
wrench

Gather the recommended tools and parts before starting
installation. Read and follow the instructions provided with
any tools listed here.

*Must be the proper size to connect your household wiring
to 16-gauge wiring in dishwasher

Make sure all these parts are included in the literature package.

NOTE: Parts available for purchase in plumbing supply stores.
Check local codes. Check existing electrical supply. See
“Electrical Requirements” section. It is recommended that
electrical connections be made by a licensed electrical installer.

® Teflon is a registered trademark of E.I. Du Pont de Nemours and Company.

Grounded electrical supply required.

Do not run drain lines, water lines or electrical wiring where
they can interfere with or contact dishwasher motor or legs.

The location where the dishwasher will be installed must
provide clearance between motor and flooring. Motor
should not touch the floor. 

Do not install dishwasher over carpeted flooring.

Protect dishwasher and water lines leading to dishwasher
against freezing. Damage from freezing is not covered by
the warranty.

A side panel kit is available from your dealer for installing
your dishwasher at the end of your cabinetry.

A moisture barrier accessory (Part No. 4396277) is available
from your dealer for installing underneath the countertop,
but is not required.

Check location where dishwasher will be installed. The
location must provide:

• easy access to water, electricity and drain.

• convenient access for loading and unloading dishes.

Corner locations require a 2” (5.1 cm) minimum 
clearance between the side of the dishwasher door 
and the wall or cabinet.

• square opening for proper operation and appearance.

• cabinet front perpendicular to floor.

• level floor. (If floor at front of opening is not level with

floor at rear of opening, shims may be needed to level
dishwasher.)

Helpful Tip: Be sure to accurately measure dimensions
and ensure dishwasher is level if the floor in the
dishwasher opening is uneven (example: flooring
extends only partway into opening).

NOTE: To prevent shifting during dishwasher operation,
shims must be securely attached to the floor.

If dishwasher will be left unused for a period of time or in a
location where it may be subject to freezing, have it
winterized by authorized service personnel.

Make sure pipes, wires and drain hose are within the
shaded area shown in the “Product and Cabinet 
Opening Dimensions” section.

90˚ Elbow fitting with 
3/8” N.P.T. external threads 
(the other end must fit your 
water supply line)

Teflon® tape or pipe joint
compound

Drain hose

2 - Drain hose clamps
(1 large and 1 small)

2 - #10 x 1/2”
Phillips-head 
screws

Green

Silver

Copper tubing (3/8” 
O.D. suggested) or 
flexible braided
water supply line

For Direct Wire: 
use UL listed or 
CSA approved  
conduit 
connector to 
fit 7/8” (2.2 cm) 
hole

See “Electrical Requirements” section

For Power Supply 
Cord: use UL 
listed power 
supply cord kit
marked for use
with dishwasher

Flashlight

Bath towel

Wood block

Shallow pan

Masking or 
duct tape

1-1/2”–2”
(38.1– 5.0 cm)
Screw-type
clamps (3 max)

Side mounting kit 
for solid surface 
countertops 
(Part No. 8212560)