Xerox 4517 用户指南
T r o u b l e s h o o t i n g
6-6 ❖ D o c u P r i n t 4 5 1 7
/
4 5 1 7 m p U s e r G u i d e
Control Panel
Messages
Listed in Table 6.2 are Control Panel messages that either:
•
Cause the printer to stop printing.
•
Require the user to call for service.
Also included in Table 6.2 are common, non-error messages
you are likely to see. The messages are listed in alphabetical
order, preceded by numerical diagnostic error codes.
Table 6.2
Control Panel messages
Message
Description/Corrective Action
0001
†
†
Appears in the upper left
corner of the display.
A fault condition has occurred.
ACTION:
Reseat the controller board and test the printer again. If the problem
continues, reseat the ROM SIMM(s) on the controller board and test
the printer again. If the problem still continues, observe the diagnostic
LED at power on. If the LED does not glow, or glows continuously,
contact your dealer or Xerox/Rank Xerox. If the LED flashes, refer to
Table 6.3 on page 6-28 for further information.
continues, reseat the ROM SIMM(s) on the controller board and test
the printer again. If the problem still continues, observe the diagnostic
LED at power on. If the LED does not glow, or glows continuously,
contact your dealer or Xerox/Rank Xerox. If the LED flashes, refer to
Table 6.3 on page 6-28 for further information.
0040
†
†
Appears in the upper left
corner of the display.
A fault condition has occurred.
ACTION:
Reseat the controller board and test the printer again. If the problem
continues, observe the diagnostic LED at power on. If the LED does
not glow, or glows continuously, contact your dealer or Xerox/Rank
Xerox. If the LED flashes, refer to Table 6.3 on page 6-28 for further
information.
continues, observe the diagnostic LED at power on. If the LED does
not glow, or glows continuously, contact your dealer or Xerox/Rank
Xerox. If the LED flashes, refer to Table 6.3 on page 6-28 for further
information.
0100
†
†
Appears in the upper left
corner of the display.
A fault condition has occurred.
ACTION:
If there is a memory SIMM in slot SIM3, remove it. Move the memory
SIMM in slot SIM2 into SIM3, then test the printer again. If code 0101
is displayed at power on, replace the SIMM. If code 0101 is not
displayed at power on, move the SIMM back to SIM2 and test the
printer again. If code 0100 again displays at power on, contact your
dealer or Xerox/Rank Xerox.
SIMM in slot SIM2 into SIM3, then test the printer again. If code 0101
is displayed at power on, replace the SIMM. If code 0101 is not
displayed at power on, move the SIMM back to SIM2 and test the
printer again. If code 0100 again displays at power on, contact your
dealer or Xerox/Rank Xerox.
0101
†
†
Appears in the upper left
corner of the display.
A fault condition has occurred.
ACTION:
If there is a memory SIMM in slot SIM2, remove it. Move the memory
SIMM in slot SIM3 into SIM2, then test the printer again. If code 0100
is displayed at power on, replace the SIMM. If code 0100 is not
displayed at power on, move the SIMM back to SIM3 and test the
printer again. If code 0101 again displays at power on, contact your
dealer or Xerox/Rank Xerox.
SIMM in slot SIM3 into SIM2, then test the printer again. If code 0100
is displayed at power on, replace the SIMM. If code 0100 is not
displayed at power on, move the SIMM back to SIM3 and test the
printer again. If code 0101 again displays at power on, contact your
dealer or Xerox/Rank Xerox.
Table 6.2 Page 1 of 22
chapter6.frm Page 6 Friday, July 11, 1997 8:19 PM