Xerox 180 安装指导
Installation Preparation Document
(for physical installation of the product only)
Xerox DocuTech 180 HighLight Color
701P46151
October 2006
October 2006
Paper Handling
•
16 to 110 lb. (60 to 200 gsm) cut sheet paper weights
•
8 by 10 in. to 14.33 x 17 in. (203 by 254 mm to 364 by 432 mm)
including A4, A3, and B4 paper sizes (destination dependent)
including A4, A3, and B4 paper sizes (destination dependent)
•
7 by 10 in. (178 by 254 mm) optional enablement kit
•
Transparencies, label stock, tab stock, carbonless paper, pre-
perforated stock
perforated stock
•
Paper stock weights less than 16 lb. are not recommended.
•
Textured stocks are not recommended.
•
Some 65 lb. stocks may not fully fuse.
Input
Tray
Capacity
Main tray (tray 1)
1,100 sheets 20 lb (75
gsm)
Auxiliary tray (tray 2)
600 sheets 20 lb (75 gsm)
High capacity trays (trays 3 and
5)
5)
2,600 sheets each 20 lb
(75 gsm)
Fuser bypass tray (tray 4)
550 sheets each 20 lb (75
gsm)
Output
Tray
Capacity
Stacker
3000 sheets 20 lb (75 gsm)
Stitcher
2 - 70 sheets 20 lb (75
gsm)
~35,000 stitches per spool
Binder
15-125 sheets 20 lb (75
gsm)
~425 11 in binds per spool
Top tray
500 sheets 20 lb (75 gsm)
Environmental Requirements
Temperature
50 to 85
o
F
(10
o
to 29
o
C)
Humidity
Non-condensation
Non-condensation
30 to 65% RH
Heat Emission - printer
4454 BTU/Hr
(Standby)
32,770 BTU/Hr
(Operating)
Altitude (above sea level)
Up to 6,000 ft
(1830 m)
Operating Supplies
Reorder No.
Dry Ink - Black
6R206 (US/CA)
Dry Ink – Blue
6R1191 (US/CA)
6R90343 (XE)
Dry Ink – Red
6R1192 (US/CA)
6R90344 (EU)
Dry Ink – Green
6R1193 (US/CA)
6R90345 (EU)
Dry Ink – Royal Blue
6R1255 (US/CA)
6R90356 (XE)
Dry Ink – Cardinal Red
6R1277(US/CA)
6R90358(XE)
Dry Ink – Cyan
6R1284(US/CA)
6R90359(XE)
Dry Ink – Magenta
6R1296 (US/CA)
6R90360 (XE)
Dry Ink – Yellow*
6R1299 (US/CA)
6R90361 (XE)
Developer (Black, Red,
Blue, Green, Royal Blue,
Cardinal Red, Cyan,
Magenta, Yellow)
Blue, Green, Royal Blue,
Cardinal Red, Cyan,
Magenta, Yellow)
NA
Fuser Blend
8R12938 (1 bottle)
8R12939 (6 bottles)
Fuser Shield
8R4077 (1 bottle)
8R7618 (6 bottles)
Dry ink waste container
NA
HLC developer waste bottle
604K24870 (4 bottles)
Binder tape – Black
8R7186
Binder tape – White
8R7187
Binder tape – Gray
8R7188
Binder tape – Blue
8R7189
Stitcher Wire
8R1174
* Will be available in the near future.
NOTE: The formula for the DocuTech HLC fuser lubricant was
changed in 2006 to provide better image quality and to prevent image
transfer. The new fuser formula is called Fuser Shield. The Fuser
Blend and the Fuser Shield CANNOT be intermixed in a DocuTech
HLC. To change from one fuser lubricant to another requires a
service call and cleaning or replacing components. The two fuser
formulas are identified with different color bottles and caps.
If a machine is running with in-line finishing equipment, the new Fuser
Shield may contribute to poor binding at the binder glue seam.
Customers experiencing this problem can have their equipment
returned to using Fuser Blend by placing a service call to clean
and/or replace components. Do NOT place Fuser Blend in a
machine that has been using Fuser Shield.
•
Monthly duty cycle is up to 6 million (DT 180 HLC).
•
The Xerox Supplies Marketing Center, 1-800-822-2200, is
available for ordering Xerox supplies, including paper and other
throughput material.
available for ordering Xerox supplies, including paper and other
throughput material.
•
The supply of developer for each of the color toners is ordered
and maintained at the customer site by the Xerox Service
Representative and is not orderable by the customer.
and maintained at the customer site by the Xerox Service
Representative and is not orderable by the customer.
•
The Dry ink waste container supply is maintained at the
customer site by the Xerox Service Representative and is not
orderable by the customer.
customer site by the Xerox Service Representative and is not
orderable by the customer.