Behringer Monitor 1C 用户指南
IMPORTANT SAFETY INSTRUCTIONS
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Be sure to mount your speakers on a solid, stable and level base or
stand. Vibrating floors do not provide reliable support for speaker
enclosures or stacks.
stand. Vibrating floors do not provide reliable support for speaker
enclosures or stacks.
8) Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
stoves, or other apparatus (including amplifiers) that produce heat.
9) Only use attachments/accessories specified by the manufacturer.
10) Use only with the cart, stand, tripod, bracket, or table specified by
the manufacturer, or sold with the apparatus. When a cart is used, use
caution when moving the cart/device combination to avoid injury from
stumbling.
the manufacturer, or sold with the apparatus. When a cart is used, use
caution when moving the cart/device combination to avoid injury from
stumbling.
11) Refer all service to qualified service personnel. Service is required
when the unit has been damaged in any way, liquid has been spilled or
objects have fallen into the apparatus, the unit has been exposed to rain
or moisture, does not operate normally, or has been dropped.
when the unit has been damaged in any way, liquid has been spilled or
objects have fallen into the apparatus, the unit has been exposed to rain
or moisture, does not operate normally, or has been dropped.
12) Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
manufacturer’s instructions.
WIRING
The MONITOR 1C is capable of producing extreme
volumes. Please note that high sound pressures may
cause temporary or even permanent hearing damage. Be
careful to select a suitable volume.
volumes. Please note that high sound pressures may
cause temporary or even permanent hearing damage. Be
careful to select a suitable volume.
Always mute your amp before connecting the speakers. Use
loudspeaker cables with a diameter of up to 4 mm (AWG 6).
loudspeaker cables with a diameter of up to 4 mm (AWG 6).
Connect your MONITOR 1C to the amplifier as shown in the
illustration: Press the connector clamps on the back of the speaker
and insert the bare end of the loudspeaker cable, paying attention
to correct polarity. Let go of the connector to secure the cable.
Connect the second loudspeaker the same way.
illustration: Press the connector clamps on the back of the speaker
and insert the bare end of the loudspeaker cable, paying attention
to correct polarity. Let go of the connector to secure the cable.
Connect the second loudspeaker the same way.
Make sure that bare wire ends never touch the open end
of another speaker cable, speaker connectors or metal
parts of your amp.
of another speaker cable, speaker connectors or metal
parts of your amp.
If you let your MONITOR 1C loudspeakers run at or
near their power limit, the integrated protective
circuitry may temporarily disconnect the tweeters.
L o w e r t h e v o l u m e t o a l l o w t h e t w e e t e r t o
automatically come online again. In this case, there
is no danger of causing permanent damage. If you
turn up treble on your amplifier, the protective
circuitry may intervene even at lower overall volume
levels.
near their power limit, the integrated protective
circuitry may temporarily disconnect the tweeters.
L o w e r t h e v o l u m e t o a l l o w t h e t w e e t e r t o
automatically come online again. In this case, there
is no danger of causing permanent damage. If you
turn up treble on your amplifier, the protective
circuitry may intervene even at lower overall volume
levels.
Version 1.1 March 2006
User’s Manual
SPECIFICATIONS
Connector type
Clip terminal
Wire diameter
< 4 mm
Power capacity (prg.) 100 W (IEC 268-5)
Impedance
Impedance
4
Ω
Frequency range
60 Hz to 23 kHz (-10 dB)
Nominal sound
pressure level (SPL)
pressure level (SPL)
86 dB*W/m (program,
bandwidth 100-5000 Hz
on axis, full space)
bandwidth 100-5000 Hz
on axis, full space)
Max. short term
acoustic output
acoustic output
112 dB @ 1m (on axis,
half space)
Tweeter
½ "
Woofer
5 ½"
Crossover frequency 5000 Hz
Dimensions (H x W x D) 8.9" x 5.9" x 5.6"
Dimensions (H x W x D) 8.9" x 5.9" x 5.6"
(225 x 150 x 142 mm)
Weight
approx. 4 lbs each
(1.8 kg each)
(1.8 kg each)
BEHRINGER is constantly striving to maintain the highest professional
standards. As a result of these efforts, modifications may be made from
time to time to existing products without prior notice. Specifications and
appearance may differ from those listed or illustrated.
standards. As a result of these efforts, modifications may be made from
time to time to existing products without prior notice. Specifications and
appearance may differ from those listed or illustrated.
MONITOR SPEAKERS 1C
ENGLISH