Heartland hcdwis 用户指南
26
Option 2: No waste disposer – with air gap:
1. Cut end of drain hose if needed (do not cut ribbed section).
2. Attach drain hose to air gap with large spring-type clamp. If the
drain hose was cut, use a 1-1/2” to 2” (3.8 to 5 cm) screw-type
clamp*.
3. Use a rubber hose connector* with spring or screw-type clamps*
to connect air gap to waste tee.
This connection must be before the drain trap and at least 20” (50.8
cm) above the floor where dishwasher will be installed.
1. Cut end of drain hose if needed (do not cut ribbed section).
2. Attach drain hose to air gap with large spring-type clamp. If the
drain hose was cut, use a 1-1/2” to 2” (3.8 to 5 cm) screw-type
clamp*.
3. Use a rubber hose connector* with spring or screw-type clamps*
to connect air gap to waste tee.
This connection must be before the drain trap and at least 20” (50.8
cm) above the floor where dishwasher will be installed.
4. Insert drain hose through
hole cut in cabinet to the front
center of opening where drain
connection will be made.
hole cut in cabinet to the front
center of opening where drain
connection will be made.
* Parts available from local plumbing
supply stores
supply stores
Option 3:Waste disposer – no air gap:
1. Remove the disposer knockout plug. Do not cut end of drain
hose.
2. Attach drain hose to disposer inlet with large spring-type clamp.
This connection must be before the drain trap and at least 20”
(50.8 cm) above the floor where dishwasher will be installed. It
is recommended that the drain hose be looped up and securely
fastened to the underside of the counter.
1. Remove the disposer knockout plug. Do not cut end of drain
hose.
2. Attach drain hose to disposer inlet with large spring-type clamp.
This connection must be before the drain trap and at least 20”
(50.8 cm) above the floor where dishwasher will be installed. It
is recommended that the drain hose be looped up and securely
fastened to the underside of the counter.
3. Insert drain hose through
hole cut in cabinet to the front
center of opening where drain
connection will be made.
hole cut in cabinet to the front
center of opening where drain
connection will be made.
Option 4: No waste disposer – no air gap:
1. Cut end of drain hose if needed (do not cut ribbed section).
2. Attach drain hose to waste tee with 1-1/2” to 2” (3.8 to 5 cm)
screw-type clamp*.
This connection must be before the drain trap and at least 20”
(50.8 cm) above the floor where dishwasher will be installed. It
is recommended that the drain hose be looped up and securely
fastened to the underside of the counter.
1. Cut end of drain hose if needed (do not cut ribbed section).
2. Attach drain hose to waste tee with 1-1/2” to 2” (3.8 to 5 cm)
screw-type clamp*.
This connection must be before the drain trap and at least 20”
(50.8 cm) above the floor where dishwasher will be installed. It
is recommended that the drain hose be looped up and securely
fastened to the underside of the counter.
3. Insert drain hose through
hole cut in cabinet to the
front center of opening where
drain connection will be
made.
hole cut in cabinet to the
front center of opening where
drain connection will be
made.
* Parts available from local plumbing
supply stores
supply stores
Install moisture barrier (optional)
1. Make sure the area under the cabinet is clean and dry for
installation of the moisture barrier.
2. Remove the backing of the moisture barrier and apply to
underside of the countertop along the front edge of the counter.
installation of the moisture barrier.
2. Remove the backing of the moisture barrier and apply to
underside of the countertop along the front edge of the counter.
drain hose –
cut here if needed
drain
hose
large
spring-type
clamp
air gap
rubber hose
connector
spring or
screw-type
clamps
waste
tee
drain trap
drain hose
drain hose
drain hose
large spring-type
clamp
disposer
inlet
drain trap
drain hose
drain
hose
waste
tee
drain trap
screw-type clamp
drain hose –
cut here if needed
drain hose
moisture
barrier