IMC Networks AccessEtherLinX, TX/4 + SSFX-SM1310-SC 852-10133 产品宣传页
产品代码
852-10133
DS-AccessEtherLinX-1010
Copyright © 2010 IMC Networks. All rights
reserved. The information in this document is
subject to change without notice. IMC Networks
assumes no responsibility for any errors that may
appear in this document. Specific product names
may be trademarks or registered trademarks and
are the property of their respective companies.
IMC Networks
Fiber Consulting Services
For information call:
TEL: 949-465-3000
1-800-624-1070
(US/CAN)
+32-16-550880
(Europe)
fcs@imcnetworks.com
IMC Networks
Headquarters
19772 Pauling
Foothill Ranch, CA 92610
TEL: 949-465-3000
FAX: 949-465-3020
sales@imcnetworks.com
IMC Networks
Europe
Herseltsesteenweg 268
B-3200 Aarschot, Belgium
TEL: +32-16-550880
FAX: +32-16-550888
eurosales@imcnetworks.com
IMC Networks
Eastern US/Latin America
28050 U.S. Hwy. 19 North, Suite 306
Clearwater, FL 33761
TEL: 727-797-0300
FAX: 727-797-0331
latinsales@imcnetworks.com
Clearwater, FL 33761
TEL: 727-797-0300
FAX: 727-797-0331
latinsales@imcnetworks.com
Ethernet Types supported:
• IEEE 802.3i Ethernet 10Base-T
• IEEE 802.3u Fast Ethernet
(100Base-TX and 100Base-FX)
• Features Auto Negotiation and Selective
Advertising
• Supports Half and Full-Duplex operation
• Includes bi-directional bandwidth
control
• Read/write IEEE 802.1Q VLAN-tags
• QoS - IEEE 802.1p-based packet
prioritization (two queues [high/low]
with eight priority levels)
• Supports IGMP multicast pruning (v1/v2)
• Layer 2 packet switching, store and
forward operation
• Includes LinkLoss and FiberAlert
• Forwarding rate: 14,881 pps for 10
Mbps; 148,810pps for 100 Mbps
• 1024 MAC address learning
• MTU: Supports over-sized packets
up to 1916 bytes
Management
• Includes GUI-based iView² software
• SNMP V1 and V2c compatible
• Supports Telnet and RS-232 Craft
• Managed through uplink
• IEEE 802.3x compliant for Flow Control
• Includes loopback test modes
(MAC Swap)
• Includes DHCP and TFTP clients for
remote management and upgrades
• Includes diagnostic LEDs
IMC MIB:
• Traps (Cold Start, Warm Start, Link Up,
Link Down, Authentication Failure)
• Link Status of Ports
• Port Type
• Fiber Type
• User-Definable Name of Product
• User-Definable ID/Name for Ports
• Enable/Disable Ports
• Enable/Disable FiberAlert
• Set for Auto Negotiation/
Selective Advertising
• Force speed and Duplex Mode for
twisted pair ports
MIB-II (RFC 1213):
• Packets Transmitted
• Packets Received
• Octets (bytes) Transmitted
• Octets (bytes) Received
• Unicast Packets Transmitted
• Unicast Packets Received
• Non-Unicast Packets Transmitted
• Non-Unicast Packets Received
• Errors Received
• Plus All Standard MIB II Objects
RMON Statistics:
• Drop Events
• Collisions
• Total Bytes
• Total Packets
• Fragments
• Jabbers
• Broadcast Packets
• Multicast Packets
• CRC Align Errors
• Under & oversize Packets
• Distribution of Frame Size
Transmission Dot 3 (RFC1643):
• Alignment Errors
• Single Collision Frames
• CRC Errors
• SQE Test Errors
• Late Collisions
• Frame Too Long
• Excessive Collisions
• Deferred Transmissions
• Multiple Collision Frames
Physical Specifications
• 50/125µm or 62.5/125µm
multi-mode fiber
• 9/125µm single-mode fiber
• Available for single-strand fiber
and CWDM fiber wavelengths
• AutoCross for automatic MDI/MDIX
switching
Connectors:
RJ-45 and ST or SC
Regulatory Approvals:
FCC Class A
UL/cUL, CSA
CE
CE
Operating Temperature:
+32° to +122° F (0° to +50° C)
Storage Temperature:
-13° to +158° F (-25° to +70° C)
Humidity:
5 to 95% (non-condensing)
Altitude:
0 to 10,000 ft.
Dimensions
1.5" H x 4.75" W x 7.25" D
(3.18 cm x 12.07 cm x 18.42 cm)
Power Rating
100-240 VAC, 50/60Hz, 1.0A
Shipping Weight:
1.6 lbs. (0.6 kg)
*
These products have single-strand fiber technology. Deploy in pairs, or connect to another compatible
IMC Networks single-strand fiber product.
Go to www.imcnetworks.com/products/SSFX.cfm for more information
Go to www.imcnetworks.com/products/SSFX.cfm for more information
Fiber Optics Specifications
For each product listed below in the Ordering Information section, the DISTANCE represents an approximate fiber distance based on industry-
standard fiber attenuation specifications. Actual distances will vary for each installation. For complete power budgets and information on calculating
specific distances, visit www.imcnetworks.com/go/fcs or contact IMC Networks Fiber Consulting Services at 949-465-3000.
Ordering Information
Technical Specifications
PART NuMBER
DESCRIPTION
DISTANCE
AccessEtherLinX/4
852-13120
TX/4 + TX
100 m
852-13121
TX/4 + FX-MM1300-ST
5 km
852-13122
TX/4 + FX-MM1300-SC
5 km
852-13123
TX/4 + FX-SM1310/PLUS-ST
40 km
852-13124
TX/4 + FX-SM1310/PLUS-SC
40 km
852-13125
TX/4 + FX-SM1310/LONG-ST
80 km
852-13126
TX/4 + FX-SM1310/LONG-SC
80 km
852-13127
TX/4 + FX-SM1550/LONG-SC
80 km
852-13130
TX/4 + FX-SM1550/XLONG-SC
100 km
AccessEtherLinX/4 Single Strand Fiber *
852-10133
TX4 + SSFX-SM1310-SC
20 km
852-10134
TX4 + SSFX-SM1550-SC
20 km
852-10135
TX4 + SSFX-SM1310/PLUS-SC
40 km
852-10136
TX4 + SSFX-SM1550/PLUS-SC
40 km
852-10137
TX4 + SSFX-SM1310/LONG-SC
60 km
852-10138
TX4 + SSFX-SM1550/LONG-SC
60 km
PART NuMBER DESCRIPTION
DISTANCE
AccessEtherLinX/4 CWDM Fiber
852-10070
TX/4 + CWDM-SM1270-SC
80 km
852-10071
TX/4 + CWDM-SM1290-SC
80 km
852-10072
TX/4 + CWDM-SM1310-SC
80 km
852-10073
TX/4 + CWDM-SM1330-SC
80 km
852-10074
TX/4 + CWDM-SM1350-SC
80 km
852-10075
TX/4 + CWDM-SM1370-SC
80 km
852-10076
TX/4 + CWDM-SM1390-SC
80 km
852-10077
TX/4 + CWDM-SM1410-SC
80 km
852-10078
TX/4 + CWDM-SM1430-SC
80 km
852-10079
TX/4 + CWDM-SM1450-SC
80 km
852-10080
TX/4 + CWDM-SM1470-SC
80 km
852-10081
TX/4 + CWDM-SM1490-SC
80 km
852-10082
TX/4 + CWDM-SM1510-SC
80 km
852-10083
TX/4 + CWDM-SM1530-SC
80 km
852-10084
TX/4 + CWDM-SM1550-SC
80 km
852-10085
TX/4 + CWDM-SM1570-SC
80 km
852-10086
TX/4 + CWDM-SM1590-SC
80 km
852-10087
TX/4 + CWDM-SM1610-SC
80 km