Sony SRF-HM03V 手册

R

L

The clock time display of this unit is a 12-hour system.
When the battery is first installed, “AM 12:00” flashes in the display.

Set POWER to OFF to turn off the power.

Hold down MEGA BASS/CLOCK for more than 2 seconds
until “AM 12” starts flashing.

Press TUNE + or – to adjust the hour, then press MEGA BASS/
CLOCK.

If you hold down 

or 

, the digit changes rapidly.

“AM 12:00 ”= midnight, “PM 12:00 ”= noon.

Repeat step 3 above to adjust the minute.

“:” starts flashing and the clock starts operating.
To set the current time exactly to the second, adjust the minute and then press

to synchronize with a time signal (such as the

telephone time signal).

If you do not press 

or 

, or 

within one minute,

the clock setting mode will be canceled.

(See fig A)

Wear the L side driver unit in your left ear and the R side in your
right ear as illustrated.

Adjust the position of the driver units for a comfortable fit.

The AM channel step differs depending on areas. The channel step of this unit is
factory-set to 10 kHz. Change the settings as shown below to be able to listen to
the radio.

North and South American countries

10 kHz

Other countries

9 kHz

When the AM channel step is changed, only the preset stations on the AM band
will be initialized.

Set POWER  to OFF to turn off the power.

While holding down MODE, hold down TUNE + or – for more
than 5 seconds.

The channel step will change and “9” kHz (or “10” kHz) will flash for 3
seconds in the display.
If you proceed to step 

 again, the channel step changes again.

Set POWER  to ON to turn on the power.

If “PRESET” is displayed, press MODE so that “PRESET”
disappears.

Pressing 

will switch over between manual tuning mode and preset

tuning mode.

Press BAND to select the band.

Each press changes the band as follows:

AM

FM

TV

WEATHER

Press TUNE + or – to select the desired frequency.

If you hold down 

or 

, the frequency or channel changes rapidly.

When the frequency matches the broadcast frequency, the broadcast will be
received.

Adjust the volume using VOL.

To turn off the radio, set 

to 

.

: Set 

 to 

if interference is

prevalent when radio wave intensity is dramatically stronger.
Under normal conditions, set to 

.

: Move around to obtain better reception.

Press 

.

“MB” appears in the display.

If the sound is distorted, or if you want to reduce the bass tone, press 

again to turn off this function.

The MEGA BASS setting is not canceled even if the radio is turned off.

You can preset up to 5 stations each for TV, WEATHER and AM, and 15
stations for FM. Also, you can delete the preset station whether it is factory-set or
preset by yourself.

Follow steps 1 to 5 in “Playing the Radio” and manually tune in to
the station you wish to preset.

Hold down ENTER until the preset number flashes.

If there is a preset number that has no preset station, that preset number
flashes.
When all the preset numbers are set to certain stations (factory-set), “1”
flashes and “PRESET” appears.

A

Press TUNE + or – to select the number you wish to preset, then
press ENTER.

When you select the preset number using 

or 

, “PRESET” appears

if that number has a preset station. If it has no preset station, only the number
flashes and “PRESET” does not appear.
When you press 

, the selected preset number lights up in the display.

: Display window when you preset FM 90.0 MHz in preset

number 2.

To preset another station, repeat these steps.
To change the preset station, preset a new station. The previous station will
be canceled.

If you do not press 

or 

, or 

within one minute, the preset

tuning mode will be canceled.

Set POWER to ON to turn on the power.

Press MODE so that “PRESET” and preset number appear.

Select the band with BAND.

Press TUNE + or – to select the desired preset number.

Adjust the volume using VOL.

To turn off the radio, set 

to 

.

If you hold down 

for more than 2 seconds, the unit enters the preset

station deleting mode. Press 

again to return to the previous mode.

Follow steps 1 and 2 in “Tuning in to a Preset Station”.

Select the band with BAND.

Press TUNE + or – to select the preset number to be deleted.

Hold down MODE for more than 2 seconds until “PRESET”,
“

dEL” and the preset number flash.

While the letters and the preset number are flashing, press
ENTER.

The station set to the preset number just before the deleted station will be
displayed.
To delete other stations, repeat steps 

 to 

.

If all the preset stations are deleted, “PRESET -” appears in the display.

To cancel deleting, press 

while “PRESET”, “dEL” and the preset number

are flashing.