KitchenAid 36" Wall-Mount Canopy Hood 安装指南
7
Range Hood Mounting Screws Installation
1. Determine and mark the centerline on the wall where the
range hood will be installed.
Based on the ceiling or soffit height, determine the distance
“X” (30" [76.2 cm] min, suggested 36" [91.4 cm] max) needed
between the cooking surface and the bottom of the range
hood. To this distance, add 11
“X” (30" [76.2 cm] min, suggested 36" [91.4 cm] max) needed
between the cooking surface and the bottom of the range
hood. To this distance, add 11
³⁄₈" (28.9 cm) and draw a
horizontal line (A) about 24" (61.0 cm) long centered on the
vertical centerline (D) at this distance.
vertical centerline (D) at this distance.
2. Mark 2 points on each side of the horizontal line
3½" (8.9 cm)
from the vertical centerline.
3. Drill 2 -
³⁄₃₂" (2.4 mm) pilot holes for installation into wood. The
screws provided are for mounting the range hood into wood;
mounting into drywall or plaster is not recommended.
mounting into drywall or plaster is not recommended.
4. Install the 2 - #10 Phillips head mounting screws. Leave a
¹⁄₄" (6.4 mm) gap between the wall and the back of the screw
head to slide range hood into place.
head to slide range hood into place.
Chimney Support Bracket Installation
1. Place one of the chimney brackets against the wall so that its
top edge is
¹⁄₁₆" (2.0 mm) from the ceiling or soffit and level.
Align the center notches of the bracket and the centerline.
Mark the centers of the bracket holes.
Mark the centers of the bracket holes.
2. Place the other chimney bracket on the wall so that its lower
edge is 16
¹⁄₁₆" (40.8 cm) from the ceiling or soffit and level.
Align the center notches of the bracket and the centerline.
Mark the centers of the bracket holes.
Mark the centers of the bracket holes.
3. Drill 4 -
³⁄₃₂" (2.4 mm) pilot holes.
4. Attach each bracket to the wall with 2 - #10 Phillips head
mounting screws. Tighten screws securely.
Complete Preparation
1. Determine and make all necessary cuts in the wall for the vent
system. Install the vent system before installing the range
hood. See the “Venting Requirements” section.
hood. See the “Venting Requirements” section.
2. Determine and mark the location where the hole will be drilled
for the power supply cable to be run through the wall.
3. Drill a 1
¹⁄₄" (3.2 cm) hole at this location.
4. Pull enough power supply cable through the wall to allow for
easy connection to the terminal box.
A. Horizontal line
B. 11
B. 11
³⁄₈
" (28.9 cm)
C. Distance “X” (30" [76.2 cm] min,
suggested 36" [91.4 cm] max)
D. Vertical centerline
E. Cooking surface
A. Horizontal line
B. Vertical centerline
B. Vertical centerline
C. 3½" (8.9 cm)
A
B
C
D
X
E
A
B
C
¹⁄₄
"
(6.4 mm)
A. Vertical centerline
B. Center notches
B. Center notches
C.
¹⁄₁₆
" (1.6 mm)
A. Distance “X” + 3" (7.6 cm)
B. 1¼" (3.2 cm) diameter
B. 1¼" (3.2 cm) diameter
C. 7¼" (18.4 cm) for 30" (76.2 cm) models
8¼" (21.0 cm) for 36" (91.4 cm) models
D. Distance “X” (30" [76.2 cm] min,
suggested 36" [91.4 cm] max)
E. Vertical centerline
F. Cooking surface
F. Cooking surface
A
B
C
(40.8 cm)
D
X
B
A
C
E
F