Xerox Phaser 3140 用户指南

Network Setup (Phaser 3160N only)_ 28

•

MAC Address : Find the machine’s MAC address from the 

Network Configuration Report and enter it without the colons. 

For example, 00:15:99:29:51:A8 becomes 0015992951A8.

•

IP Address: Enter a new IP address for your printer.
For example, if your computer’s IP address is 192.168.1.150, 

enter 192.168.1.X. (X is number between 1 and 254 other than 

the computer’s address.)

•

Subnet Mask: Enter a Subnet Mask.

•

Default Gateway: Enter a Default Gateway.

6. Click Apply, and then click OK. The machine will automatically print 

the Network Configuration Report. Confirm that all the settings are 

correct.

7. Click Exit to close the SetIP program.
8. If necessary, restart the computer’s firewall.

For using SetIP program, disable the computer firewall before continuing 

by performing the following:
1. Open System Preferences.
2. Click Security.
3. Click the Firewall menu.
4. Turn firewall off.

The following instructions may vary for your model.

1. Connect your machine to the network with a network cable.
2. Insert the Installation CD-ROM, and open the disk window, select 

MAC_Installer > MAC_Printer > SetIP > SetIPapplet.html.

3. Double click the file and Safari will automatically open, then select 

Trust. The browser will open the SetIPapplet.html page that shows 

the printer’s name and IP address information. 

4. Click on the   icon (third from left) in the SetIP window to open the 

TCP/IP configuration window.

5. Enter the machine’s new information into the configuration window 

as follows. In a corporate intranet, you may need to have this 

information assigned by a network manager before proceeding.

•

MAC Address : Find the machine’s MAC address from the 

Network Configuration Report and enter it without the colons. 

For example, 00:15:99:29:51:A8 becomes 0015992951A8.

•

IP Address: Enter a new IP address for your printer.
For example, if your computer’s IP address is 192.168.1.150, 

enter 192.168.1.X. (X is number between 1 and 254 other than 

the computer’s address.)

•

Subnet Mask: Enter a Subnet Mask.

•

Default Gateway: Enter a Default Gateway.

6. Select Apply, then OK, and OK again. The printer will automatically 

print the configuration report. Confirm that all the settings are correct. 

Quit Safari. You may close and eject the installation CD-ROM. If 

necessary, restart the computer’s firewall. You have successfully 

changed the IP address, subnet mask, and gateway.

SetIP program should be automatically installed during the printer driver 

installation.
1. Print the machine’s network configuration report to find your 

machine’s MAC address. 

2. Open the /opt/Xerox/mfp/share/utils/.
3. Double click the SetIPApplet.html file. 
4. Click to open the TCP/IP configuration window. 
5. Enter the network card’s MAC address, IP address, subnet mask, 

default gateway, and then click Apply. 

When you enter the MAC address, enter it without a colon(:).

6. The machine prints the network configuration report. Confirm all the 

settings are correct. 

7. Close the SetIP program. 

You can also set up the various network settings through the network 

administration programs such as CentreWare IS.

You may need to reset the machine to the factory default settings when 

machine that you are using is connected to new network environment.

1. Start a web browser such as Internet Explorer, Safari or Firefox and 

enter your machine’s new IP address in the browser window.
For example,

2. When the CentreWare IS window opens, click Properties > 

General.

3. Click Reset. Then, click on the button below to restroe defaults.

4. Turn off and restart machine to apply settings.