Xerox DocuColor 12 Printer with Fiery XP12 文件
Customer Expectation Setting Document for
Fiery XP12 with version 1.1 Software, Digital Front End for DocuColor 12
April 25, 2000
2
Terms and product names used in this document may be trademarks or registered trademarks of their respective companies and are hereby acknowledged.
Environmental Requirements
Min.
Max.
Operating Temperature
50
o
F (10
o
C)
104
o
F (40
o
C)
Humidity (noncondensing)
5% RH
95% RH
Altitude (above sea level)
0
10,000 ft.
(3,048 m)
Server Specifications (minimum)
•
500 MHz Pentium III Processor
•
256 MB RAM (additional 256 MB optional)
•
9.2 GB IDE hard drive (6.6 GB available for printing/ storage)
•
10/100 BaseT Network capability
•
The XP12 is fully Y2K compliant.
Network Connectivity
Protocol Stack
Printing
Services
Supported Frame Types
Platform
Novell IPX / SPX
PServer
Ethernet 802.2
Ethernet 802.3
Ethernet_II
Ethernet SNAP
Token Ring 802.2 (option)
Token Ring SNAP
(option)
(option)
Windows NT 4.0
Windows 95, 98
Windows 2000
TCP / IP
LPD/LPR
Ethernet_II
Token Ring SNAP
(option)
(option)
Windows NT 4.0
Windows 95, 98
Windows 2000
SunOS 4.1.x
TCP / IP
SMB
Ethernet_II
Token Ring SNAP
(option)
(option)
Windows NT 4.0
Windows 95, 98
Windows 2000
AppleTalk
PAP
Ethernet SNAP
(EtherTalk Phase 2 only)
Windows NT 4.0
Macintosh
Parallel Port
LPT1
N/A
Windows NT 4.0
Windows 95,98
Windows 2000
The customer is responsible for supplying one network drop to enable the install.
Printing Specifications
PostScript
The Fiery XP12 is a true Adobe PostScript 3 controller with PDF
native printing.
native printing.
PCL 5e Emulation
POWER PAGE
Print Speed / System Performance
•
The maximum print speed for the XP12 system is limited by the
print speed of the DocuColor 12.
print speed of the DocuColor 12.
•
DocuColor 12 is a document printer; therefore in reverse order
printing the print engine will not cycle up until the entire job is ready.
This will impact First Copy Out Time (FCOT). The copier may cycle
down between each job depending on job complexity.
printing the print engine will not cycle up until the entire job is ready.
This will impact First Copy Out Time (FCOT). The copier may cycle
down between each job depending on job complexity.
•
Overall system performance (‘Click to Clunk’ time) is primarily
dependent upon the software applications and network environment
being used. Rasterizing (RIP-ing) is only a small fraction of Click to
Clunk time.
dependent upon the software applications and network environment
being used. Rasterizing (RIP-ing) is only a small fraction of Click to
Clunk time.
•
Printing with custom software applications may produce unexpected
or unknown results.
or unknown results.
•
The Performance Series controllers provide accurate billing of all
color and black & white images in black detection mode.
color and black & white images in black detection mode.
Maximum Image Sizes
•
The maximum image size from an application is limited to the image
size produced by DocuColor 12. The application and the DocuColor
12 setup controls image position.
size produced by DocuColor 12. The application and the DocuColor
12 setup controls image position.
•
Non-imageable area for the DocuColor 12 is listed as follows:
Leading
Edge
Trailing
Edge
Near Edge
Far Edge
3mm
3mm
3mm
3mm
Paper
Size
Image Size
SR A3
303 x 438 mm
12” x 18”
297 x 438 mm
ECT Compression
•
The Compression efficiency is dependent on file type and
complexity. Artifacts may be possible when compression is selected
depending on the file complexity.
depending on the file complexity.
Calibration
•
AutoCal2 is the primary calibration method.
•
An optional X-Rite DTP32 densitometer is available with the XP12
server to enable the printer calibration feature. Currently the X-Rite
DTP32 is the only densitometer approved for the Fiery XP12.
server to enable the printer calibration feature. Currently the X-Rite
DTP32 is the only densitometer approved for the Fiery XP12.
•
Color monitor calibration is the responsibility of the customer.
•
Optimal print quality is achieved by using a densitometer. For RGB
emitting applications (PowerPoint, Word, and Excel), use the
DocuColor 12 calibration target. For CMYK applications (Quark,
Pagemaker) use the SWOP target.
emitting applications (PowerPoint, Word, and Excel), use the
DocuColor 12 calibration target. For CMYK applications (Quark,
Pagemaker) use the SWOP target.
Print Quality and Color Management
•
The appearance of the document displayed on the monitor screen
may not match the output print because the monitor uses RGB
color space parameters.
may not match the output print because the monitor uses RGB
color space parameters.
•
For imported RGB images, optimal color is achieved in the EPS
format. Other imported file formats may produce unexpected
results.
format. Other imported file formats may produce unexpected
results.
Separations Support
•
For the PC, only QuarkXPress & PageMaker should be used for
separations.
separations.
•
For the Mac, only QuarkXPress 4.0 or PageMaker version 6.5 can
be used for separations.
be used for separations.
Scanning Specifications
The copier does support the Scan Back feature using a TWAIN plug-in.
Any application that supports a TWAIN interface will be able to utilize
this feature (i.e. PhotoShop, TextBridge, etc.). The following table
represents the scan resolution specs for various image sizes:
Any application that supports a TWAIN interface will be able to utilize
this feature (i.e. PhotoShop, TextBridge, etc.). The following table
represents the scan resolution specs for various image sizes:
Image Size
XP12 (Memory: 256 MB)
Letter (8.5X11)
Max 400 dpi
Tabloid (11X17)
Max 400 dpi
A4
Max 400 dpi
A3
Max 400 dpi