Honeywell LinevoltPRO™ 7000 Digital Non-Programmable Electric Heat Thermostat (TL7235A1003) 安装指南
TL7130A/TL7135A/TL8130A/TL7230A/TL7235A/TL8230A
69-1804EFS 30/6/05 1/2
•
One (1)power base
•
Two (2) screws
•
Four (4) solderless connectors for copper wires.
NOTE:
Special CO/ALR solderless connectors must be used when
connecting with aluminum conductors.
TURN OFF POWER TO THE HEATING SYSTEM AT THE MAIN POWER
PANEL TO AVOID ELECTRICAL SHOCK.
The installation must be carried out by an electrician.
PANEL TO AVOID ELECTRICAL SHOCK.
The installation must be carried out by an electrician.
Install the thermostat onto an electrical box.
Install the thermostat about 5 feet high, on an inside wall facing the
heater.
heater.
Avoid locations where there are air drafts (such as the top of a staircase
or an air outlet), dead air spots (such as behind a door), or direct sun-
light.
or an air outlet), dead air spots (such as behind a door), or direct sun-
light.
Do not install the thermostat on a wall that conceals chimney or stove
pipes.
pipes.
n
Loosen the captive screw under-
neath the thermostat.
neath the thermostat.
o
Separate the control module from
the power base by pulling the bot-
tom sections apart.
the power base by pulling the bot-
tom sections apart.
p
Connect the power and heater
wires to the corresponding wires
of the power base.
wires to the corresponding wires
of the power base.
q
Push the wires into the electrical
box.
box.
r
Secure the power base to the
electrical box using the supplied
screws.
electrical box using the supplied
screws.
s
If there are any switches on the back of the control module for configur-
ing the thermostat, place them in the appropriate positions.
ing the thermostat, place them in the appropriate positions.
t
Install the control module back onto the base.
u
Apply power to the heating system.
Storage
: -4°F to 120°F (-20°C to 50°C)
Size (H • W • D)
: 4.9 x 2.7 x 0.9 in. (124 x 70 x 23 mm)
Certifications
:
•
Una (1) base de alimentación
•
Dos (2) tornillos
•
Cuatro (4) conectores sin soldadura para hilos de cobre.
NOTA :
Deben usarse conectores sin soldadura CO/ALR especiales
cuando se conecten conductores en aluminio.
CORTAR LA ALIMENTACIÓN DEL SISTEMA DE CALEFACCIÓN EN EL
PANEL PRINCIPAL PARA EVITAR RIESGOS DE CHOQUE ELÉCTRICO
Un electricista debe hacer la instalación
PANEL PRINCIPAL PARA EVITAR RIESGOS DE CHOQUE ELÉCTRICO
Un electricista debe hacer la instalación
Instalar el termostato en una caja de electricidad.
Instalarlo alrededor de 1.5 m sobre el nivel del suelo y en una pared inte-
rior que esté frente al calefactor.
rior que esté frente al calefactor.
Deben evitarse los lugares con corrientes de aire (en lo alto de una
escalera o en una salida de aire), los puntos en los que el aire no circule
(detrás de una puerta) o la luz directa del sol.
escalera o en una salida de aire), los puntos en los que el aire no circule
(detrás de una puerta) o la luz directa del sol.
No debe instalarse el termostato en una pared que oculte un conducto
de chimenea o de calefacción.
de chimenea o de calefacción.
n
Aflojar el tornillo cautivo que está
debajo del termostato.
debajo del termostato.
o
Separar el módulo de control de la
base de alimentación tirando de
ambos en la base.
base de alimentación tirando de
ambos en la base.
p
Conectar los cables de alimen-
tación y los del calentador a los
correspondientes de la base de
alimentación.
tación y los del calentador a los
correspondientes de la base de
alimentación.
q
Empujar los cables en la caja de
electricidad.
electricidad.
r
Asegurar la base de alimentación
a la caja de electricidad con los tornillos proporcionados.
a la caja de electricidad con los tornillos proporcionados.
s
Configurar los selectores que haya en la parte posterior del módulo de
control (si fuera necesario).
control (si fuera necesario).
t
Instalar el módulo de control nuevamente en su base.
u
Alimentar en electricidad el sistema de calefacción.
Almacenamiento
: -4°F a 120°F (-20°C a 50°C)
Dimensiones (Alto • Ancho • Profundidad)
: 4.9 x 2.7 x 0.9 in. (124 x 70 x 23 mm)
Certificaciones
:
n
Parts supplied
1.
o
Guidelines
2.
p
Procedure
3.
q
Technical Specifications
4.
Models
Supply
Max. Load
Power
Wiring
TL7230A
TL7235A
TL8230A
TL7235A
TL8230A
240 VAC, 50/60Hz
208 VAC, 50/60Hz
208 VAC, 50/60Hz
15 A
3600 W
3120 W
3120 W
4w/DP
TL7130A
TL7135A
TL8130A
TL7135A
TL8130A
240 VAC, 50/60Hz
208 VAC, 50/60Hz
208 VAC, 50/60Hz
16.7 A
4000 W
3470 W
3470 W
4w/SP
Power
Heater
n
Materiales provistos
5.
o
Instrucciones
6.
p
Procedimiento
q
Especificaciones técnicas
7.
Modelos
Alimentación
carga máxima
Potencia
Cableado
TL7230A
TL7235A
TL8230A
TL7235A
TL8230A
240 VAC, 50/60Hz
208 VAC, 50/60Hz
208 VAC, 50/60Hz
15 A
3600 W
3120 W
3120 W
4w/DP
TL7130A
TL7135A
TL8130A
TL7135A
TL8130A
240 VAC, 50/60Hz
208 VAC, 50/60Hz
208 VAC, 50/60Hz
16.7 A
4000 W
3470 W
3470 W
4w/SP
Alimentación (línea)
Sistema de calefacción
Guía de instalación
Base de alimentación
Installation Guide
Power Base
TL7130A/TL7135A/TL8130A/TL7230A/TL7235A/TL8230A