Gorenje WT 62093 用户手册

GB 3

GB 2

a.  Cut and remove the shrink-wrap.
b.  Remove the top protection and the protective 

corners.

machine bottom.  

This is important, as otherwise the plastic part could 

damage the washing machine during operation.

d.  Open the lid by pressing it slightly down while 

raising the handle. Remove the polystyrene 

cushion (depending on model).

e.  Remove the blue protective film from the panel 

(depending on model).

•  After unpacking, make sure that the washing 

machine is undamaged. If in doubt, do not use the 

washing machine. Contact After-Sales Service or 

your local retailer.

•  Keep the packaging materials (plastic bags, 

polystyrene parts, etc.) out of reach of children; 

they are potentially dangerous.

•  If the appliance was exposed to the cold prior to 

delivery, keep it at room temperature for a few 

hours before operating.

•  The washing machine is fitted with transport 

screws and a transport bracket to prevent damage 

during transport. 

bracket (see “Installation”/“Removal of transport 

bracket”).

•  Place the washing machine on a flat and stable 

floor surface.

•  In case of wooden or so-called “floating floors” (for 

instance certain parquet or laminate floors), place 

the appliance on a sheet of plywood with a size of 

at least 40 x 60 cm and thickness of at least 3 cm, 

which is screwed to the floor.

•  Make sure that the ventilation openings in the 

base of your washing machine (if available on your 

model) are not obstructed by a carpet or other 

material.

•  Connect the water supply inlet hose in accordance 

with the regulations of your local water company 

(see “Installation”/“Connect the water inlet hose”).

•  Water supply: Cold water only
•  Tap: 3/4” threaded hose connection
•  Pressure: 100-1000 kPa (1-10 bar).

•  Only use new hoses for connecting the washing 

machine to the water supply. Used hoses must not 

be used anymore and should be discarded.

•  Firmly connect the drain hose to the siphon or 

another outlet for drain water. (see “Installation”/

Connect the water drain hose”).

•  If the washing machine is connected to a built-in 

drainage system, ensure the latter is equipped with 

a vent to avoid simultaneous loading and draining 

of water (siphoning effect).

•  Electrical connections must be carried out by a 

qualified technician in compliance with the manu-

facturer’s instructions and the current standard 

safety regulations.

•  The technical data (voltage, power and fuses) are 

given on the rating plate on the rear of the washing 

machine.

•  Do not use extension leads or multi sockets.
•  Access to the mains plug or disconnection from 

the mains supply via a double-pole switch must be 

ensured at all times after the installation.

•  Do not operate the washing machine if it has been 

damaged during transport. Inform the After-Sales 

Service.

•  Mains cable replacement is only to be carried out 

by After-Sales Service.

•  The washing machine must be connected exclu-

sively by means of a socket with an earth connec-

tion, in compliance with the regulations in force. In 

particular, washing machines installed in premises 

containing a shower or a bath must be protected 

by a differential residual current device of at least 

30 mA. Earthing the washing machine is obliga-

tory under the law. The manufacturer declines all 

liability for injury to  persons or animals or damage 

to property deriving either directly or indirectly from 

failure to observe the directions in these Instruc-

tions for Use.

•  When using a residual current circuit breaker 

(RCCB), only use a model marked with 

.

Approximate dimensions:

Width:  

400 mm

Height:  

900 mm

Depth:  

600 mm

DESCRIPTION OF THE WASHING MACHINE (picture 1)

a.  Lid
b. Detergent dispenser
c.  Drum
d. Pump access behind filter
e. After-Sales Service sticker (behind the filter cover)

f.  Mobility lever (depending on model). To move the 

washing machine: pull the handle out a little bit by 

hand and pull it out to the stop with the foot.

g. Adjustable feet 

The washing machine is fitted with a transport bracket 

to avoid any possible damage during transport.
IMPORTANT: Before using the washing machine, 

removed.
1.  Unscrew the two screws “A” and the four screws 

“

B” with a flat screwdriver or a No. 8 hex nut box 

spanner (picture 

2).

2.  Remove the transport bracket (picture 3).
3.  Replace the four outer screws “B” on the machine 

and tighten them (picture

 2).

4.  Clip the two covers “C” supplied into the openings 

“

D” of the washing machine (picture 4).

Adjust the feet (picture 5, 6)

Install the washing machine on a level surface, near 

to electrical, water and drain connections.
If the floor is uneven, adjust the feet (do not insert 

pieces of wood, cardboard etc. under the feet):
1.  Screw out the washing machine´s feet by hand 

with 2-3 clockwise turns and then slacken the 

locknut by wrench.

2.  Adjust the height of the feet by hand.
3.  Retighten the locknut by turning it anti-clockwise 

towards the washing machine’s bottom.

level and stable (use a spirit level).
The washing machine can be installed in an area 40 

cm wide and 63 cm deep.
Note: if you install the machine on thick carpet, adjust 

the feet to ensure that there is sufficient space under 

the machine for the air to circulate.

Connect the water inlet hose (picture 7)

1.  Carefully screw the water inlet hose to the valve 

on the rear side of the washing machine (

A); screw 

the other end of the hose to the tap by hand.

2.  Make sure there are no kinks in the hose.
3.  Check water-tightness of tap and washing machine 

connections by turning the tap completely on.

•  If the hose is too short, replace it with a suitable 

length of pressure  resistant hose (1000 kPa min, 

EN 61770 approved type).

•  If you need a longer waterstop hose, contact our 

After Sales Service or your dealer.

•  Check the inlet hose regularly for brittleness and 

cracks and replace if necessary.

•  The washing machine can be connected without a 

backflow valve.

Water stop anti-flooding system (picture 8)

(if available)
•  Screw the hose to the water supply tap. Turn the 

tap fully on and check the water-tightness of the 

connection.

•  The washing machine must not be connected to 

the mixing tap of a non-pressurized water heater!

•  Do not immerse the water stop device of the hose 

into water; otherwise it will loose its protective 

function.

•  If the flexible hose is damaged, unplug the washing 

machine from the mains immediately, turn off the 

tap and replace the hose.

•  If the flexible hose is too short, replace it with a 3 

m Water Stop hose (available from After-Sales 

Service or from your dealer).

Connect the water drain hose (picture 9)

Unhook the drain hose from the left clip, see arrow 

“

A” on picture.

nection, see arrow “B” on picture. Otherwise, there 

is the risk of leakage and of scalding with hot water.
Firmly connect the drain hose to the siphon or another 

outlet for drain water.

If you need to add an extension, use a flexible hose 

of the same size and secure the unions with screw-on 

hose clips. 

Maximum overall drain hose length: 2.50 m. 

Maximum drain height: 100 cm. 

Minimum drain height: 55 cm.
Important:

Make sure there are no kinks in the drain hose and 

take precautions against it falling while the washing 

machine is running.