Cisco Cisco IOS Software Release 12.4(4)T
DSP Operational State Notifications
snmp-server enable traps
7
Cisco IOS Release 12.4(4)T
Syntax Description
Command Default
All notification types controlled by this command are enabled.
Command Modes
Global configuration
notification-type
(Optional) Type of notification (trap or inform) to enable or disable. If no type
is specified, all notifications available on your device are enabled or disabled
(if the no form is used). The notification type can be one of the following
keywords:
is specified, all notifications available on your device are enabled or disabled
(if the no form is used). The notification type can be one of the following
keywords:
•
config—Controls configuration notifications, as defined in the
CISCO-CONFIG-MAN-MIB (enterprise 1.3.6.1.4.1.9.9.43.2). The
notification type is (1) ciscoConfigManEvent.
CISCO-CONFIG-MAN-MIB (enterprise 1.3.6.1.4.1.9.9.43.2). The
notification type is (1) ciscoConfigManEvent.
•
ds0-busyout—Sends notification when the busyout of a DS0 interface
changes state (Cisco AS5300 platform only). This notification is defined
in the CISCO-POP-MGMT-MIB (enterprise 1.3.6.1.4.1.9.10.19.2), and
the notification type is (1) cpmDS0BusyoutNotification.
changes state (Cisco AS5300 platform only). This notification is defined
in the CISCO-POP-MGMT-MIB (enterprise 1.3.6.1.4.1.9.10.19.2), and
the notification type is (1) cpmDS0BusyoutNotification.
•
ds1-loopback—Sends notification when the DS1 interface goes into
loopback mode (Cisco AS5300 platform only). This notification type is
defined in the CISCO-POP-MGMT-MIB (enterprise 1.3.6.1.4.1.9.10.19.2)
as (2) cpmDS1LoopbackNotification.
loopback mode (Cisco AS5300 platform only). This notification type is
defined in the CISCO-POP-MGMT-MIB (enterprise 1.3.6.1.4.1.9.10.19.2)
as (2) cpmDS1LoopbackNotification.
•
dsp —Enables SNMP digital signal processing (DSP) traps. This
notification type is defined in the CISCO-DSP-MGMT-MIB.
notification type is defined in the CISCO-DSP-MGMT-MIB.
•
dsp oper-state—Sends a DSP notification made up of both a DSP ID that
indicates which DSP is affected and an operational state that indicates
whether the DSP has failed or recovered.
indicates which DSP is affected and an operational state that indicates
whether the DSP has failed or recovered.
•
entity—Controls Entity MIB modification notifications. This notification
type is defined in the ENTITY-MIB (enterprise 1.3.6.1.2.1.47.2) as
(1) entConfigChange.
type is defined in the ENTITY-MIB (enterprise 1.3.6.1.2.1.47.2) as
(1) entConfigChange.
•
hsrp—Controls Hot Standby Routing Protocol (HSRP) notifications, as
defined in the CISCO-HSRP-MIB (enterprise 1.3.6.1.4.1.9.9.106.2). The
notification type is (1) cHsrpStateChange.
defined in the CISCO-HSRP-MIB (enterprise 1.3.6.1.4.1.9.9.106.2). The
notification type is (1) cHsrpStateChange.
•
ipmulticast—Controls IP multicast notifications.
•
modem-health—Controls modem-health notifications.
•
rsvp—Controls Resource Reservation Protocol (RSVP) flow change
notifications.
notifications.
•
tty—Controls TCP connection notifications.
•
xgcp—Sends External Media Gateway Control Protocol (XGCP)
notifications. This notification is from the XGCP-MIB-V1SMI.my, and
the notification is enterprise 1.3.6.1.3.90.2 (1) xgcpUpDownNotification.
notifications. This notification is from the XGCP-MIB-V1SMI.my, and
the notification is enterprise 1.3.6.1.3.90.2 (1) xgcpUpDownNotification.
Note
For additional notification types, see the Related Commands table.
vrrp
(Optional) Specifies the Virtual Router Redundancy Protocol (VRRP).