Cisco Cisco 2106 Wireless LAN Controller 發佈版本通知
55
Release Notes for Cisco Wireless LAN Controllers and Lightweight Access Points for Release 4.2.61.0
OL-31336-01
Caveats
•
CSCsi78368—The client packet dot1p check, which performs the client’s tos-to-DSCP translation,
is not supported in controller software release 4.2 for packets from wireless clients to the network.
The priority is always mapped to 0 (null). This problem occurs when you configure the “qos profile”
for platinum, gold, silver, or bronze and the “wired qos protocol” for type = 802.1p and tag = N.
This issue affects the priority field in the dot1p vlan header tag for the 4.2 release, so clients on
VLANs are affected.
is not supported in controller software release 4.2 for packets from wireless clients to the network.
The priority is always mapped to 0 (null). This problem occurs when you configure the “qos profile”
for platinum, gold, silver, or bronze and the “wired qos protocol” for type = 802.1p and tag = N.
This issue affects the priority field in the dot1p vlan header tag for the 4.2 release, so clients on
VLANs are affected.
•
CSCsi80732—When you configure the b/g radio with all the data rates disabled except for 24, 36,
48, and 54 Mbps, which are configured as mandatory, the controller refuses the association of a
wireless client that correctly provides the four supported rates.
48, and 54 Mbps, which are configured as mandatory, the controller refuses the association of a
wireless client that correctly provides the four supported rates.
•
CSCsi81630—The controller might reboot repeatedly around 5 minutes after startup. This condition
usually occurs when the controller, acting as a client station, attempts to associate with a rogue
access point.
usually occurs when the controller, acting as a client station, attempts to associate with a rogue
access point.
•
CSCsi90962—When an access point tries to join a controller but fails AAA authorization, an SNMP
trap is not generated to show the failure.
trap is not generated to show the failure.
•
CSCsi91600—The user’s home page leads back to the reauthentication page if a redirect URL is
populated.
populated.
•
CSCsj02690—For 1000 series access points, beacons come at irregular intervals on the 2.4-GHz
band.
band.
•
CSCsj10736—The controller sends query packets at the wrong interval.
•
CSCsj18577—After you upgrade to controller software release 4.1.171.0 or later and configure
WPA1 or WPA2 with PSK, the syslog server might display the following message:
“AAA-5-RADSERVER_NOT_FOUND: Couldn't find appropriate Radius server for VAP 6. Reason:
Radius accounting is disabled.”
WPA1 or WPA2 with PSK, the syslog server might display the following message:
“AAA-5-RADSERVER_NOT_FOUND: Couldn't find appropriate Radius server for VAP 6. Reason:
Radius accounting is disabled.”
•
CSCsj19875—When the controller reports the following error, it fails to include the MAC address
of the client. Instead, it reports the MAC address of one of its own access points.
of the client. Instead, it reports the MAC address of one of its own access points.
Thu Jun 7 12:25:19 2007 Client Association Failure: MAC Address:00:15:70:17:8f:69 Base
Radio MAC:00:14:f2:7d:be:00 Slot: 0 Reason:Unspecified ReasonCode: 1
Radio MAC:00:14:f2:7d:be:00 Slot: 0 Reason:Unspecified ReasonCode: 1
•
CSCsj20565—A 4400 series controller might reboot when you click Monitor > CDP > Interface
Neighbors on the controller GUI in software release 4.1.171.0 or later.
Neighbors on the controller GUI in software release 4.1.171.0 or later.
•
CSCsj35158—You cannot make changes to the User Base DN, User Attributes, and User Object
Type parameters on an existing LDAP server configuration on the 2006 controller. After making
changes and choosing Apply, the page shows the server index as zero and blank entries. Also, the
changes are not saved after you re-edit the parameters.
Type parameters on an existing LDAP server configuration on the 2006 controller. After making
changes and choosing Apply, the page shows the server index as zero and blank entries. Also, the
changes are not saved after you re-edit the parameters.
•
CSCsj35964 and CSCsi97060—A hybrid-REAP access point might reboot under the following
conditions:
conditions:
–
The WLAN has WMM allowed.
–
The radio policies are set to something other than All, such as 802.11b/g Only.
–
The 802.11a network is disabled.
–
Changes are made to the WLAN configuration (such as enabling or disabling the SSID).
The hybrid-REAP configuration (VLAN mappings) might also become lost, requiring a manual
reconfiguration to enable them.
reconfiguration to enable them.
•
CSCsj40291 and CSCsg05961—Controller software release 4.1.171.0 or later does not encapsulate
broadcast traffic in the LWAPP tunnel. As a result, broadcast traffic is not sent from a server
application to the wireless clients.
broadcast traffic in the LWAPP tunnel. As a result, broadcast traffic is not sent from a server
application to the wireless clients.