Cisco Cisco 5508 Wireless Controller 技术参考
28
Cisco Aironet 1600/2600/3600 Series Access Point Deployment Guide
External Antenna Options and Patterns
The DAS vendor and systems integrator are solely responsible for the support of the DAS products,
adequate RF coverage, and any RF-related issues. This support includes, but is not exclusive to, location
accuracy, RF coverage, roaming issues related to RF, multipath issues, and scalability.
adequate RF coverage, and any RF-related issues. This support includes, but is not exclusive to, location
accuracy, RF coverage, roaming issues related to RF, multipath issues, and scalability.
The DAS vendor and systems integrator are also responsible for understanding that the deployed DAS
system meets the requirements of all of the customer Wi-Fi devices and applications over the DAS
system; this statement includes, but is not exclusive to, all Voice over WLAN (VoWLAN) and medical
devices.
system meets the requirements of all of the customer Wi-Fi devices and applications over the DAS
system; this statement includes, but is not exclusive to, all Voice over WLAN (VoWLAN) and medical
devices.
While Cisco Technical Assistance Center (TAC) and Cisco field teams do not provide support for RF
issues that arise in a Cisco WLAN used over a DAS, they do provide support for non-RF related issues
in Cisco products according to the customer support agreement with Cisco Systems.
issues that arise in a Cisco WLAN used over a DAS, they do provide support for non-RF related issues
in Cisco products according to the customer support agreement with Cisco Systems.
For more information, see the following URL:
Elevators
Elevator coverage can sometimes be accomplished by placing APs in the near field of the elevator,
typically on each floor near the elevator door. Since elevators often have metal doors, and the shafts are
often concrete or contain other materials that degrade Wi-Fi coverage, it is important to check the
coverage inside the elevator. Elevator coverage can be a challenge, but it is often possible, especially if
the elevator only serves a few floors.
typically on each floor near the elevator door. Since elevators often have metal doors, and the shafts are
often concrete or contain other materials that degrade Wi-Fi coverage, it is important to check the
coverage inside the elevator. Elevator coverage can be a challenge, but it is often possible, especially if
the elevator only serves a few floors.
In high rise elevators, roaming issues are more problematic because the client cycles through a large
number of APs rather quickly. Some companies put a patch antenna on the floor inside the shaft and a
patch antenna on the bottom of the elevator car, while other companies use leaky coaxial cable along the
side of the shaft.
number of APs rather quickly. Some companies put a patch antenna on the floor inside the shaft and a
patch antenna on the bottom of the elevator car, while other companies use leaky coaxial cable along the
side of the shaft.
When installing any Wi-Fi equipment inside elevator cars or shafts, follow local regulations. Some
installations may be prohibited because of safety reasons, while other installations may be prohibited by
the building owner or local fire department. Only elevator repair persons or experienced contractors
should perform this type of work.
installations may be prohibited because of safety reasons, while other installations may be prohibited by
the building owner or local fire department. Only elevator repair persons or experienced contractors
should perform this type of work.
External Antenna Options and Patterns
AP 1600/2600 and AP 3600e
The following dual-band, dual-resonant antennas are available for use with the AP 1600e*/2600e and
the AP 3600e:
the AP 3600e:
AIR-ANT2524DB-R – Dual-band (Black) dipole (4 required) – 2/4 dBi Dipole
AIR-ANT2524DW-R – Dual-band (White) dipole (4 required) – 2/4 dBi Dipole
AIR-ANT2524DG-R – Dual-band (Grey) dipole (4 required) – 2/4 dBi Dipole
AIR-ANT2524V4C-R – Dual-band Omni-directional (1 required) – 2/4 dBi Ceiling mount Omni use
AIR-ANT2544V4M-R – Dual-band Omni-directional (1 required) – 4/4 dBi Wall mount Omni use
AIR-ANT2566P4W-R – Dual band directional (1 required) – 6 dBi Patch wall mount use