Cisco Cisco Aironet 1200 Access Point 發佈版本通知
15
Resolved Caveats
OL-3159-01
Caveats
•
CSCdy73695—When a repeater access point receives packets from a root access point while the
repeater is attempting to associate, the repeater sometimes displays this error:
repeater is attempting to associate, the repeater sometimes displays this error:
00:00:10 (Warning): Station <Root MAC address> Associated with Encryption, then
attempted to send an Unencrypted packet to <Repeater MAC address> (length 74)
The error occurs when WEP is not enabled on either the root or the repeater. When an association
response is received by the repeater, it no longer displays the error message and is able to
successfully pass data. However, if a significant amount of traffic, such as multicast traffic, is being
transmitted by the root access point while the repeater is attempting to associate, the repeater may
miss the association response from the root access point and never fully associates. In this case, the
root access point reports that the repeater is associated and the repeater reports that it is only
authenticated. The repeater continues to display warning messages about receiving unencrypted
packets and does not recover until it is rebooted.
response is received by the repeater, it no longer displays the error message and is able to
successfully pass data. However, if a significant amount of traffic, such as multicast traffic, is being
transmitted by the root access point while the repeater is attempting to associate, the repeater may
miss the association response from the root access point and never fully associates. In this case, the
root access point reports that the repeater is associated and the repeater reports that it is only
authenticated. The repeater continues to display warning messages about receiving unencrypted
packets and does not recover until it is rebooted.
•
CSCdx80069—The access point sometimes incorrectly buffers packets for wireless phones in power
save mode. This may cause certain wireless phones to lock up for short periods of time.
save mode. This may cause certain wireless phones to lock up for short periods of time.
Workaround: Other than operating the phone in CAM mode, there is no workaround for this
problem.
problem.
•
CSCdx81372—Access point does not accept version 11.56-generated .ini file
If you download the full configuration .ini from an access point running 11.56, upgrade to version
12.00T, and then attempt to download the .ini file from an FTP server, the following error message
displays:
12.00T, and then attempt to download the .ini file from an FTP server, the following error message
displays:
*** No Such MIB Variable as Specified on Initialization File Line xxx! for the
following variables:
awcAaaServerAccountingEnabled.x,
awcVoIPVlanId, awcVoIPVlanEnabled,
awcPublicVlanId.
*** Bad Value for MIB Variable awcVlanEncapMode Specified on Initialization File Line
xxx (error 13)!
Workaround—When producing .ini files, dump a non-default configuration for version 11.56
instead of a full configuration.
instead of a full configuration.
Resolved Caveats
The following caveats are resolved in version 12.00T:
•
CSCdy25035—You no longer need to reboot the access point when you enable or change accounting
parameters. The access point now uses all the accounting parameters directly from the MIB, making
all changes effective immediately.
parameters. The access point now uses all the accounting parameters directly from the MIB, making
all changes effective immediately.
•
CSCdw53237—When you change the access point’s role in radio network from repeater to root, the
link from the access point to the previous root device no longer remains active.
link from the access point to the previous root device no longer remains active.
•
CSCdy72082—The MIB variable bootconfigBootCount can now be accessed using SNMP.
•
CSCdy72838—When you enable WEP, MIC and TKIP on a repeater access point and configure the
repeater to LEAP authenticate, the repeater operates normally.
repeater to LEAP authenticate, the repeater operates normally.
•
CSCdw83703—The access point no longer reports a could not allocate error when LEAP-enabled
workgroup bridges are associated.
workgroup bridges are associated.