Cisco Cisco StadiumVision Mobile 發佈版本通知
© 2011 Cisco Systems, Inc. All rights reserved.
18 of 26
3. The DHCP Server will then send the DMP its network settings plus Option 43 for the SV
Director’s IP Address.
4. Next, using the SV Director IP address, the DMP will register itself with SV Director. From the
SV Director Control Panel, the operator can then map the DMP to the TV location and its
associated groups and zones.
associated groups and zones.
Notes:
•
Auto registration works only with the DMP 4310. It is not supported on the DMP 4305.
•
Auto registration requires that the DMP 4310 be running build 1932 or later. Earlier versions do
not have this feature.
not have this feature.
•
The DMP 4310 ships as a SV specific version (DMP-4310G-SE-K9) and a generic version
(DMP-4310G-52-K9). The hardware is identical, but the firmware loaded at the factory is
different. The DMP-4310G-52-K9 ships with version 5.2 firmware and supports auto registration.
When a DMP-4310G-52-K9 registers with SV Director it will be upgraded to the correct
StadiumVision version.
(DMP-4310G-52-K9). The hardware is identical, but the firmware loaded at the factory is
different. The DMP-4310G-52-K9 ships with version 5.2 firmware and supports auto registration.
When a DMP-4310G-52-K9 registers with SV Director it will be upgraded to the correct
StadiumVision version.
•
Auto registration requires that DHCP remain enabled on the DMPs. By default SVD is configured
to disable DHCP. In order to use auto-registration you must first change the DHCP setting under
Global DMP Setting to ‘On’. See the
to disable DHCP. In order to use auto-registration you must first change the DHCP setting under
Global DMP Setting to ‘On’. See the
Control Panel Enhancements
The Control Panel Setup > Control screen has been redesigned to show as many event states on
the screen as possible. The event state details were simplified to include only the Start / Cancel /
Stop status. Additionally, functionality was added so you can schedule event staging ahead of time.
the screen as possible. The event state details were simplified to include only the Start / Cancel /
Stop status. Additionally, functionality was added so you can schedule event staging ahead of time.
Multiple Simultaneous Event Scripts
You can now run multiple event scripts simultaneously. This enables the capability to push content
targeted for a group of screens in a specific area of the venue for example, back offices, club areas,
and luxury suites.
targeted for a group of screens in a specific area of the venue for example, back offices, club areas,
and luxury suites.
You can also obtain proof of play reports for multiple simultaneous event scripts.
Notes:
•
You cannot run event scripts simultaneously if two or more of the event scripts control the same
DMP. This will cause a conflict or overlap between the event scripts. Should this occur, the first
event script will run but any subsequent event scripts that attempt to control the same DMP will
be blocked and will not run.
DMP. This will cause a conflict or overlap between the event scripts. Should this occur, the first
event script will run but any subsequent event scripts that attempt to control the same DMP will
be blocked and will not run.
•
If a script is blocked, you can mouse over the “blocked” status in the Control Panel Control tab
to view a list of the conflicting event scripts.
to view a list of the conflicting event scripts.
•
To run multiple event scripts simultaneously, you need to create separate zones for separate
event scripts.
event scripts.
•
There is no automatic notification to the event operator when an event script is blocked.
However, SV Director displays a warning message in the Control Panel Control tab. When
running event scripts simultaneously, the event operator should periodically check the Control
tab to see if there is a warning message.
However, SV Director displays a warning message in the Control Panel Control tab. When
running event scripts simultaneously, the event operator should periodically check the Control
tab to see if there is a warning message.
•
A blocked event script becomes unblocked when all conflicting event scripts are stopped. You
can cancel an event script which is blocked or an event script which has completed staging but
can cancel an event script which is blocked or an event script which has completed staging but