Sony MKS-2010 用户手册
Ch
apt
e
apt
e
r 2
N
a
mes
and
Fun
c
tions
of
P
of
P
a
rt
s
16
Control Panel Configuration
than key buses. For key buses, you can select any of the
following three options as the operating mode when a
snapshot is recalled with this button on.
• Cross-point hold (retain the current cross-point selection
following three options as the operating mode when a
snapshot is recalled with this button on.
• Cross-point hold (retain the current cross-point selection
state)
• Key disable (retain the current key settings)
• Key disable, plus retention of the current key on/off
• Key disable, plus retention of the current key on/off
states
See “Setting the key bus cross-point hold mode” (page
173) for more information about how to set the operating
mode.
173) for more information about how to set the operating
mode.
e SHIFT button
Press this button, turning it on, to use the cross-point
buttons as shift side buttons. Press this button again,
turning it off, to use the cross-point buttons as non-shift
side buttons.
Press this button, turning it on, to use the cross-point
buttons as shift side buttons. Press this button again,
turning it off, to use the cross-point buttons as non-shift
side buttons.
f Cross-point button row
These buttons select the signals to be output to the bus
selected with the AUX delegation buttons.
The signals which can be selected with each cross-point
button are the same as the signals selected by the
corresponding buttons in the M/E cross-point control
block (see page 12). Button numbers and the meaning of
the colors in which the buttons light are the same as those
of the buttons in the M/E cross-point control block.
However, the cross-point button row in the AUX bus
control block contains an [M/E] button and a [PGM]
button, which are not present in the M/E cross-point button
rows. The [M/E] button selects the M/E program video,
and the [PGM] button selects the program video (final
output video).
These buttons select the signals to be output to the bus
selected with the AUX delegation buttons.
The signals which can be selected with each cross-point
button are the same as the signals selected by the
corresponding buttons in the M/E cross-point control
block (see page 12). Button numbers and the meaning of
the colors in which the buttons light are the same as those
of the buttons in the M/E cross-point control block.
However, the cross-point button row in the AUX bus
control block contains an [M/E] button and a [PGM]
button, which are not present in the M/E cross-point button
rows. The [M/E] button selects the M/E program video,
and the [PGM] button selects the program video (final
output video).
M/E Transition Control Block
Use this block to control transitions in M/E (mix/effect)
program video.
program video.
FRAMES
NEXT TRANSITION
OVER
OVER
KEY
PRIOR
BKGD
KEY1
KEY2
TRANSITION TYPE
MIX
EFF
AUTO
TRANS
CUT
PST
COLOR
MIX
FRAMES
NEXT TRANSITION
OVER
OVER
KEY
PRIOR
KEY1
ON
BKGD
KEY1
KEY2
KEY2
ON
TRANSITION TYPE
MIX
EFF
AUTO
TRANS
CUT
PST
COLOR
MIX
1
Transition execution section
2
Next transition selection buttons
3
OVER indicators
4
Transition type
selection buttons
selection buttons
1
Transition execution
section
section
M/E transition control
block on 1.5 M/E panel
and 1.5 M/E wide panel
block on 1.5 M/E panel
and 1.5 M/E wide panel
2
Next transition
selection buttons
selection buttons
3
OVER indicators
4
Transition type
selection buttons
selection buttons
5
KEY1 ON and KEY2
ON buttons
ON buttons
M/E transition control
block on 1 M/E panel
block on 1 M/E panel