Sony STR-DE698 用户手册
masterpage:Left
lename[E:\SEM_Janet\DATA_STR-
DE698_Revision5\J9050000_2560571141DE698_UCA\2560571141\GB03CON_STR-DE698-
UCA.fm]
UCA.fm]
model name1[STR-DE698]
[2-560-571-14(1)]
20
GB
x
/
XXXXXX
(Surround back speaker selection)
• DUAL
If you connect two surround back speakers,
select “DUAL”. The sound will be output to a
maximum of 7.1 channels.
select “DUAL”. The sound will be output to a
maximum of 7.1 channels.
• SINGLE
If you connect only one surround back
speaker, select “SINGLE”. The sound will be
output to a maximum of 6.1 channels.
speaker, select “SINGLE”. The sound will be
output to a maximum of 6.1 channels.
• NO
If you did not connect surround back speaker,
select “NO”.
select “NO”.
Tips
• a)–c) correspond to the following Dolby Pro Logic
modes
a)
NORMAL
b) PHANTOM
c)
c)
3 STEREO
• The “LARGE” and “SMALL” settings for each
speaker determine whether the internal sound
processor will cut the bass signal from that channel.
When the bass is cut from a channel, the bass
redirection circuitry sends the corresponding bass
frequencies to the sub woofer or other “LARGE”
speakers.
However, since bass sounds have a certain amount of
directionality, it is best not to cut them, if possible.
Therefore, even when using small speakers, you can
set them to “LARGE” if you want to output the bass
frequencies from that speaker. On the other hand, if
you are using a large speaker, but prefer not to have
bass frequencies output from that speaker, set it to
“SMALL”.
If the overall sound level is lower than you prefer, set
all speakers to “LARGE”. If there is not enough bass,
you can use the BASS parameter in the EQ menu to
boost the bass levels. To adjust the bass, see page 39.
processor will cut the bass signal from that channel.
When the bass is cut from a channel, the bass
redirection circuitry sends the corresponding bass
frequencies to the sub woofer or other “LARGE”
speakers.
However, since bass sounds have a certain amount of
directionality, it is best not to cut them, if possible.
Therefore, even when using small speakers, you can
set them to “LARGE” if you want to output the bass
frequencies from that speaker. On the other hand, if
you are using a large speaker, but prefer not to have
bass frequencies output from that speaker, set it to
“SMALL”.
If the overall sound level is lower than you prefer, set
all speakers to “LARGE”. If there is not enough bass,
you can use the BASS parameter in the EQ menu to
boost the bass levels. To adjust the bass, see page 39.
x
DIST. X.X m (XX ft.)
(Front speaker distance)
Initial setting: 3.0 m (10 ft.)
Lets you set the distance from your listening position
to the front speakers (A). You can adjust from 1.0
meter to 7.0 meters (3 to 23 feet) in 0.1 meter (1 foot)
steps.
to the front speakers (A). You can adjust from 1.0
meter to 7.0 meters (3 to 23 feet) in 0.1 meter (1 foot)
steps.
If both front speakers are not placed an equal distance
from your listening position, set the distance to the
closest speaker.
from your listening position, set the distance to the
closest speaker.
When placing only one surround back speaker
When placing two surround back speakers
(The angle E should be the same)
x
DIST. X.X m (XX ft.)
(Center speaker distance)
Initial setting: 3.0 m (10 ft.)
Lets you set the distance from your listening position
to the center speaker. Center speaker distance should
be set from a distance equal to the front speaker
distance (A) to a distance 1.5 meters (5 feet) closer to
your listening position (B).
to the center speaker. Center speaker distance should
be set from a distance equal to the front speaker
distance (A) to a distance 1.5 meters (5 feet) closer to
your listening position (B).
SBL
SBR
SB
L
R
D
30˚
30˚
100˚-120˚
100˚-120˚
A
C
C
A
B
30˚
30˚
100˚-120˚
100˚-120˚
A
A
C
E
E
E
B
C
D
D
C
GB01COV_STR-DE698-UCA.book Page 20 Monday, June 27, 2005 12:18 PM