Eaton Electrical char-lynn 230 用户手册
110, 230, and 450 Series Steering Control Units
2
See Note Below (lower right)
Cast
End
Cap
End
Cap
Special Tools Available
600057-000 Spring Installation Tool
5422-000 12 Point Drive Socket ( 5/16 in.) — -001
64489-000 6 Point (E10) Torx Drive Socket ( 5/16 in.) — -002
Note: Current -002 uses a Hex Head bolt – 1/2 inch across flats
600057-000 Spring Installation Tool
5422-000 12 Point Drive Socket ( 5/16 in.) — -001
64489-000 6 Point (E10) Torx Drive Socket ( 5/16 in.) — -002
Note: Current -002 uses a Hex Head bolt – 1/2 inch across flats
O-ring Groove
Cap Screws 12 Pt. Drive No. 5389-XXX, Spacer Plate 7970, and End
Cap, 8438 are -001 Parts. If any one of these parts needs replacing, order
Kit listed in chart (below) by displacement. Kit parts will update your
steering control unit to -002 design level.
Note: When installing kit parts, gerotor outer ring will have to be turned
so the o-ring groove faces the end cap (gerotor star—if the spline is full
length ring and star can be turned together, but if star has a
partial spline turn ring only, this partial splined star must
remain unturned). Replacement spacer plate will have a
o-ring groove, position this groove toward gerotor.
Cap, 8438 are -001 Parts. If any one of these parts needs replacing, order
Kit listed in chart (below) by displacement. Kit parts will update your
steering control unit to -002 design level.
Note: When installing kit parts, gerotor outer ring will have to be turned
so the o-ring groove faces the end cap (gerotor star—if the spline is full
length ring and star can be turned together, but if star has a
partial spline turn ring only, this partial splined star must
remain unturned). Replacement spacer plate will have a
o-ring groove, position this groove toward gerotor.
O-ring Groove
3
4
7 3
6
9
1
2
5
3
23
22
9
31
30
10
8
17
13
14 13
15
18
19
16
Previous Manual
Steering Check Valve
Steering Check Valve
W
U
V
X
Y Z
11
12
11
11
Low Input Torque
Spring (4)/Spacer (2)
Package
Spring (4)/Spacer (2)
Package
Standard Input Torque
Spring (6)
Package
Spring (6)
Package
Note: All housing valves are factory adjusted on
assembled units to a code designation and are
not to be changed. This housing (with specified
valve pressure settings), the mating spool, and
the sleeve are not practical replacement parts.
assembled units to a code designation and are
not to be changed. This housing (with specified
valve pressure settings), the mating spool, and
the sleeve are not practical replacement parts.
Ref.
No.
No.
Description
Ref.
No.
No.
Description
Ref.
No.
No.
Description
16
Seal, 24,9 mm [.98 in.] ID
19
Ring, Retaining
18
Bushing, Seal Gland
15
Seal, 47,2 mm [1.86 in.] ID
17
Seal, Quad Ring, 26,7 mm [1.05 in.] ID
13
Bearing Race
14
Bearing, Needle Thrust
23
Pin, Roll, 34,92 mm [1.375 in.] Length
22
Ball, 6,35 mm [.250 in.] OD
8
Housing
9
Sleeve, Control/Spool, Control
11
Spring, Centering
12
Spring, Spacer
Pin, Centering
3
Seal, 72,6 mm [2.86 in.] ID
6
Plate, Spacer
7
Drive
4
Gerotor
5
Spacer
1
Cap Screw, Hex Head
10
2
Cap, End
30
Ball, Check
31
Pin, Roll, 40,00 mm [1.575 in.] Length
V
W
X
Y
Y
Seal — 9,2 mm [.36 in.] ID
Z
Screw, Set
Seat, Check Ball
U
Seal — 7,6 mm [.30 in.] ID
Ball, Check
Retainer, Check Ball
*