Crestron qs sw-dat c2n-dap8 rc 用户手册
Crestron DAT Software
Digital Audio Tools
NOTE: The level adjustments done here are in addition to the values set in the Room Calibration tab. The
total gain or attenuation is represented at the bottom of each slider.
total gain or attenuation is represented at the bottom of each slider.
Options: These are available for adjustment for music decoding modes only. The following
describes which options apply to which modes and what changes they cause to the mode.
Panorama, Center Width, and Dimension apply to Dolby Pro Logic II Music.
describes which options apply to which modes and what changes they cause to the mode.
Panorama, Center Width, and Dimension apply to Dolby Pro Logic II Music.
Panorama: Extends the front stereo image to include the surround speakers for a
wraparound effect with sidewall imaging.
wraparound effect with sidewall imaging.
Center Width: Allows variable adjustment of the center image so it may be heard
only from the center speaker, only from the left/right speakers as a “phantom” center
image, or various combinations of all three front speakers. Adjust for your listening
preference. Valid entries are 0 through 7.
only from the center speaker, only from the left/right speakers as a “phantom” center
image, or various combinations of all three front speakers. Adjust for your listening
preference. Valid entries are 0 through 7.
Dimension: Allows an adjustment of the sound field either towards the front or
towards the rear. Adjust for your listening preference. Valid entries are 0 through 3.
towards the rear. Adjust for your listening preference. Valid entries are 0 through 3.
Center Gain applies to DTS Neo6: Music:
Center Gain: Allows variable adjustment of the center image so it may be heard only
from the center speaker, only from the left/right speakers as a “phantom” center
image, or combinations of all three front speakers. Useable adjustment is 0 to 0.5.
from the center speaker, only from the left/right speakers as a “phantom” center
image, or combinations of all three front speakers. Useable adjustment is 0 to 0.5.
Graphic EQ
Use this tab to select the amount of Graphic/ Parametric EQ’s to be used for each channel. You can also make
adjustments for all speakers among 10 presets. The adjustments made here will affect all active speakers.
adjustments for all speakers among 10 presets. The adjustments made here will affect all active speakers.
EQ Mode: This describes the current Graphic/ Parametric configuration of the EQ’s and
allows the selection of different configurations. The default is 5 Graphic EQ’s/ 1 Parametric
EQ. When choosing to make a change to the default settings, you are prompted to let you
know the effect this will have on the processor. The options available are as follows:
allows the selection of different configurations. The default is 5 Graphic EQ’s/ 1 Parametric
EQ. When choosing to make a change to the default settings, you are prompted to let you
know the effect this will have on the processor. The options available are as follows:
0 Graphic EQ’s/ 6 Parametric EQ’s:
There are no graphic EQ frequencies available.
3 Graphic EQ’s/ 3 Parametric EQ’s:
The graphic EQ frequencies available for adjustment are:
250
Hz.
1000
Hz.
4000
Hz.
5 Graphic EQ’s/ 1 Parametric EQ:
The graphic EQ frequencies available for adjustment are:
63 Hz.
250
Hz.
1000
Hz.
4000
Hz.
10000
Hz.
EQ Trim Preset: Use this drop-down to select the preset you would like to adjust. There are
up to 10 presets available for the graphic EQ’s. All presets affect all active speakers in the
system.
up to 10 presets available for the graphic EQ’s. All presets affect all active speakers in the
system.
Quick Start – DOC. 6238
Digital Audio Processors: C2N-DAP8/RC
•
7