SECO-LARM USA enforcer ev-122c-dvb3q 用户手册

ENFORCER

Ball-Mount Indoor/Outdoor IR Camera Manual

ENFORCER

Ball-Mount Indoor/Outdoor IR Camera Manual

Dimensions:

_______________________________________________________________________________________________________________________________________________________________

Parts List

1 x Camera Ball
1 x Case
1 x Base
4 x Screws with wall anchors
1 x Hex wrench
1 x Manual
1 x DC plug with terminal block

Before Starting:

1. Please read this manual carefully and keep it for future

reference.

2. Use the camera within given temperature and electrical

limits.

3. While the camera is weatherproof to IP66 standard, do

not mount the camera where it is exposed to rain or other
moisture, or in humid or dusty places.

4. Do not point the camera at the sun. Heat could damage

the camera, even when not in use.

5. Do not mount the camera in areas exposed to radiation,

Installation:
1. Run a 12VDC power supply wire and a video cable

with a male BNC connector through the wall to where
the camera is to be mounted.

2. Loosen the set screws with the included hex wrench

and remove the case from the base.
NOTE - The camera ball is NOT attached to the case
or the base. It sits loose inside the case. Therefore, be
very careful when removing the case from the base to
not drop the camera ball.

3. Mount the base to the wall using the four included

mounting screws. If the wall is made of dry wall, brick,
or similar material, it may be necessary to use the
included plastic screw anchors.

strong magnetic fields, or strong electrical signals.*

6. Do not open or disassemble the camera. There are

no user-serviceable parts inside.

7. Do not drop the camera or subject it to strong

vibrations.

* Note: Many video monitors produce strong

electromagnetic fields close to the display CRT,
especially when the monitor is turned on or during de-
Gaussing, which occurs automatically with many
monitors when the monitor is turned on.

4. Run the camera's BNC and power connectors through

the camera base, and connect to the video and power
wires that were run through the wall.

5. Put the case over the camera ball onto the base, being

careful to not drop the camera ball.

6. Holding the case loosely on the base, turn the camera

ball to the desired direction.

7. Once the camera ball is in the desired direction, tighten

the set screws with the included hex wrench. However,
do not tighten them too tightly. Tighten just enough so
that the case does not move, and the camera ball does
not rotate.

8. Do a final test of the video camera and the monitor.

Case

Camera

Ball

Base

4 x

Screws

Power

Connector

BNC

Connector

” (94mm)

”

(80mm)

To BNC

(From DC
camera)

DC plug included.

DC plug with

terminal block

Type

Chip

Resolution

Pickup elements

Scanning system

Sync

Video output

Lens

IR LEDs

IR distance

IR view angle

Minimum illumination

Gamma correction

S/N ratio

Shutter control

Automatic gain control

White balance

Power source

Power consumption

Operating temperature

Enclosure

Dimensions

Weight

Cable length

EV-122C-DVB3Q

Ball-Mount Color Dome Camera

1/3” CCD, Sony

420 TV lines

510 x 492 pixels

2:1 interlace, V: 59.94Hz, H: 15.734KHz

Internal

1V p-p composite output, 75 ohms

3.6mm, F2.0

24 x LEDs (850nm)

Up to 50’ (15m)

0.5 lux (0 lux with IR on)

0.45

>48dB

Auto Electronic Shutter (AES), 1/60~1/100,000 sec.

Auto

12VDC ±10%

120mA (IR off), 400mA (IR on)

4°~122° F (-20°~50° C)

IP66 weatherproof

” x 3

” (94 x 80mm)

0.9 lb. (400g)

38” (98cm.)

Specifications