Snapper 9265 用户手册
3
IMPORTANT SAFETY INSTRUCTIONS
OPERATIONAL PRECAUTIONS
(Continued From Previous Page)
7. DO NOT put hands or feet near or under
7. DO NOT put hands or feet near or under
rotating parts. Keep clear of the discharge
opening at all times.
opening at all times.
8. Start engine only where exhaust fumes will be
safely dissipated. Allow a brief warm-up period,
and practice operation of controls outside
before putting the machine to work.
and practice operation of controls outside
before putting the machine to work.
9. After striking a foreign object, STOP the engine
(motor), remove the key, and remove the wire
from spark plug. Thoroughly inspect the snow
thrower for any damage, and repair the damage
before restarting and operating the snow
thrower.
from spark plug. Thoroughly inspect the snow
thrower for any damage, and repair the damage
before restarting and operating the snow
thrower.
10. STOP the engine if the machine starts to vibrate
excessively as this normally indicates
mechanical problems. Remove the key and
disconnect the spark plug wire to prevent
unintentional starting before servicing or
repairing the machine.
mechanical problems. Remove the key and
disconnect the spark plug wire to prevent
unintentional starting before servicing or
repairing the machine.
11. DO NOT clear snow across the face of slopes.
Exercise extreme CAUTION when changing
direction on slopes. DO NOT attempt to clear
steep slopes.
direction on slopes. DO NOT attempt to clear
steep slopes.
12. DO NOT leave machine unattended with the
engine running. STOP engine and remove key
to prevent unauthorized operation.
to prevent unauthorized operation.
13.
Release clutch control and make sure
auger/impeller has STOPPED before adjusting
deflector, or placing hands near auger/impeller.
auger/impeller has STOPPED before adjusting
deflector, or placing hands near auger/impeller.
14. DO NOT use snow thrower on surfaces above
ground level, such as, a roof of a building.
15. Exercise extreme CAUTION when operating on
or crossing gravel drives, walks, or roads. Stay
alert for hidden hazards or traffic.
alert for hidden hazards or traffic.
16. DO NOT overload the machine capacity by
attempting to clear snow at too fast a rate.
17. Never operate the machine at high transport
speeds on slippery surfaces. Look behind and
use care when backing.
use care when backing.
18. Disengage power to the auger/impeller when
snow thrower is transported or not in use.
19.
Use only attachments and accessories
approved by the manufacturer of the snow
thrower (such as wheels weights,
counterweights, cabs and the like).
approved by the manufacturer of the snow
thrower (such as wheels weights,
counterweights, cabs and the like).
20. Never operate the snow thrower without good
visibility or light. Always be sure of your
footing, and keep a firm hold on the handles.
Walk; never run.
footing, and keep a firm hold on the handles.
Walk; never run.
MAINTENANCE AND STORAGE
1. DO NOT store machine or fuel container inside
where fumes may reach an open flame, spark,
or pilot light as in a water heater, furnace,
clothes dryer or other gas appliance. Allow
engine to cool before storing machine in an
enclosure. Store fuel container out of reach of
children in a well ventilated, unoccupied
building.
or pilot light as in a water heater, furnace,
clothes dryer or other gas appliance. Allow
engine to cool before storing machine in an
enclosure. Store fuel container out of reach of
children in a well ventilated, unoccupied
building.
2. Keep machine and engine free of excess oil,
grease and spilled fuel to reduce fire hazard.
3. When draining fuel tank, drain fuel into an
approved container outdoors and away from
open flame.
open flame.
4. Inspect all bolts, nuts and screws frequently
and keep properly tightened.
5. Use only recommended shear bolts (if
equipped) to prevent possible damage to
machine.
machine.
6. Service engine and make adjustments only
when engine is stopped. Remove key, remove
wire from spark plug, secure wire away from
plug, and disconnect cord from electric starting
motors to prevent accidental starting.
wire from spark plug, secure wire away from
plug, and disconnect cord from electric starting
motors to prevent accidental starting.
7. DO NOT change engine governor speed
settings or overspeed engine.
8. DO NOT test for spark by grounding the spark
plug next to spark plug hole. Spark from the
plug could ignite gas exiting engine.
plug could ignite gas exiting engine.
9. Have machine serviced by an authorized
SNAPPER dealer at least once a year and have
the dealer install any new safety devices.
the dealer install any new safety devices.
10. Use only genuine SNAPPER replacement parts
to assure that original standards are
maintained.
maintained.