Ariens sno-thro 932103 - 624 用户手册
GB - 16
Secure unit chassis to transport vehicle.
NEVER secure from rods or linkages that
could be damaged.
DO NOT transport machine while engine is
running.
NEVER secure from rods or linkages that
could be damaged.
DO NOT transport machine while engine is
running.
SERVICE POSITION
Place unit on a flat level surface. Before tipping
unit up onto housing, remove enough fuel so
no spills will occur. Tip unit forward onto front
of Impeller housing for service. Assure unit is
secure and will not tip over. Strap and clamp
onto bench if needed.
unit up onto housing, remove enough fuel so
no spills will occur. Tip unit forward onto front
of Impeller housing for service. Assure unit is
secure and will not tip over. Strap and clamp
onto bench if needed.
MAINTENANCE SCHEDULE
The chart below shows the recommended
maintenance schedule that should be
performed on a regular basis. More frequent
service may be required.
maintenance schedule that should be
performed on a regular basis. More frequent
service may be required.
*
After first two hours of operation.
CHECK FASTENERS
Make sure all hardware is tightened properly.
CHECK ATTACHMENT CLUTCH
Auger / impeller must stop within 3 seconds
when attachment clutch bail is released or unit
damage or serious injury may result.
If clutch does not engage or disengage
properly, adjust or repair before operation (see
Service and Adjustments).
when attachment clutch bail is released or unit
damage or serious injury may result.
If clutch does not engage or disengage
properly, adjust or repair before operation (see
Service and Adjustments).
CLEAN ENGINE
Refer to Engine Manual for detailed
instructions.
instructions.
CHECK ENGINE OIL
The engine crankcase oil should be checked
every 5 hours of operation. Oil level MUST be
maintained in safe operating range on dipstick
at all times or engine damage will result (See
Engine Manual).
Park unit on a level surface. Refer to Engine
Manual for detailed instructions.
every 5 hours of operation. Oil level MUST be
maintained in safe operating range on dipstick
at all times or engine damage will result (See
Engine Manual).
Park unit on a level surface. Refer to Engine
Manual for detailed instructions.
CHANGE ENGINE OIL
Change oil after first two (2) hours of
operation, thereafter change oil every 25
hours (more often if required). Refer to Engine
Manual for detailed instructions.
NOTE: Sno-Thro has an oil drain cut-out on
the left side of unit frame. Drain engine oil
through this cut-out to prevent spills.
operation, thereafter change oil every 25
hours (more often if required). Refer to Engine
Manual for detailed instructions.
NOTE: Sno-Thro has an oil drain cut-out on
the left side of unit frame. Drain engine oil
through this cut-out to prevent spills.
CHECK TIRE PRESSURE
Keep tires at pressure listed on the tire
sidewall.
sidewall.
CHECK AUGER GEARCASE
IMPORTANT: Proper oil level must be
maintained.
Gear cases are filled to the correct level at the
factory. Unless there is evidence of leakage,
no additional lubricant should be required.
Check oil level each season or every 25 hours
of operation.
maintained.
Gear cases are filled to the correct level at the
factory. Unless there is evidence of leakage,
no additional lubricant should be required.
Check oil level each season or every 25 hours
of operation.
MAINTENANCE
WARNING: AVOID INJURY. Read
and understand Maintenance and
Service/Fuel Safety Rules before
proceeding.
and understand Maintenance and
Service/Fuel Safety Rules before
proceeding.
MAINTENANCE SCHEDULE
Each
Use
Use
Every
5 hrs.
5 hrs.
Every
25 hrs.
25 hrs.
Yearly
Check
Fasteners
Fasteners
•
Check
Attachment
Clutch
Attachment
Clutch
•
Clean
Engine
Engine
•
Check
Engine Oil
Engine Oil
•
Change
Engine Oil
Engine Oil
*
•
Check Tire
Pressure
Pressure
•
Check Auger
Gearcase
Gearcase
•
•
General
Lubrication
Lubrication
•
•