temco-tool 39tdvp 用户手册

29

WARNING: This HI/LO conversion kit must ONLY be 
applied as part of a conversion kit supplied by the 
appliance manufacturer for the specific appliance 
and type of gas being converted.
The conversion shall be carried out in accordance 
with the requirements of the provincial authori-
ties having jurisdiction and in accordance with the 
requirements of the CSA B149.2 Installation Code 
(Canada) and with the requirements of the National 
Fuel Gas Code Z223.1/NFPA 54 (United States).
WARNING: This conversion kit shall be installed 
by a qualified service agency in accordance with 
the manufacturer’s instructions and all applicable 
codes and requirements of the authority having 
jurisdiction. If the information in this instruction is 
not followed exactly, a fire, explosion or production 
of carbon monoxide may result causing property 
damage, personal injury or loss of life. The qualified 
service agency is responsible for the proper instal-
lation of this kit. The installation is not proper and 
complete until the operation of the converted appli-
ance is checked as specified in the manufacturer’s 
instructions supplied with the kit.
Installer Notice: Using an ink pen, fill out the re-
quired information on the conversion label. Remove 
the backing from label and stick label in a visible 
position on bottom of fireplace close to gas valve.
Installer Notice: These instructions must be left 
with the appliance.
Instructions for converting your fireplace from Natural 
gas to Propane/LP gas.
All fireplaces are shipped from the factory equipped to 
operate on Natural gas. To convert the fireplace to op-
erate on Propane/LP gas, follow the instructions below. 
Please see the appropriate parts list for your model for 
parts included with the fireplace.
Check the items in the kit with the parts list. Notify the 
supplier of any items that are missing before installing 
the conversion kit. 
1.  Turn off gas supply.
2.  Turn off the electrical supply to the appliance if so 

equipped.

1.  Remove the two (2) screws holding the pilot to the 

burner bracket.

2.  Remove lava rock to expose screws and remove 

grate assembly.

3.  Use screwdriver and bend burner tabs outward. (Fig. 

44)

4.  Loosen the split nut assembly to remove from 

burner/air shutter. Slide burner tube to the left and 
off burner orifice. (Fig. 44)

5.  Using a suitable tool replace natural orifice #47 with 

propane orifice #56 for model 33TDVP, or replace 
natural orifice #45 with propane orifice #55 for model 
36TDVP, or replace natural orifice #42 with propane 
orifice #54 for model 39TDVP furnished with conver-
sion kit. Tighten orifice with suitable tool until gas 
tight. (Fig. 45)

6.  Move burner tube back to original position, tighten 

split nut assembly and bend tabs back up.

7.  Set the air shutter opening for propane/LP gas.  (Re-

fer to Figure 46 and Chart on Page 34) Tighten air 
shutter screw.

T207

air shutter 

setting

1/8/04  djt

T207

Fig. 46  Air shutter settings for propane/LP gas.

3/8” - 33TDVP
3/8” - 36TDVP
3/8” - 39TDVP

Fig. 45  Replace burner orifice with correct conversion orifice.

T259

remove burner

orifice

6/04

Split Nut Assembly

Air Shutter

Burner Orifice

T259

Fig. 44  Bend tabs down, loosen split nut assembly and slide 
burner tube to the left.

T257

fuel conversion

6/04

Burner Tabs

Split Nut Assembly

T257

  NOTE: Failure to adjust air shutter to proper setting 

will produce sooting.

8.  Fasten pilot to burner bracket with two (2) screws.
9.  Replace grate assembly.