GE 28106 用户手册

10330 North Meridian Street

Indianapolis, IN 46290

© 2007 Thomson Inc. 

Trademark(s) ® Registered

Marca(s) Registrada(s)

Model 28106 

00019389 (Rev. 0 Dom E/S) 

07-15 

Printed in China

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two 

conditions: (1) This device may not cause harmful interference; and (2) This device must accept 

any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital 

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable 

protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed 

and used in accordance with the instructions, may cause harmful interference to radio 

communications. However, there is no guarantee that interference will not occur in a 

particular installation.
Privacy of Communications may not be ensured when using this product.
If this equipment does cause harmful interference to radio or television reception, which can 

be determined by turning the equipment off and on, the user is encouraged to try to correct 

the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna (that is, the antenna for radio or television that 

is “receiving” the interference).

• Reorient or relocate and increase the separation between the telecommunications 

equipment and receiving antenna.

• Connect the telecommunications equipment into an outlet on a circuit different from that 

to which the receiving antenna is connected.

If these measures do not eliminate the interference, please consult your dealer or an 

experienced radio/television technician for additional suggestions. Also, the Federal 

Communications Commission has prepared a helpful booklet, “How To Identify and Resolve 

Radio/TV Interference Problems.” This booklet is available from the U.S. Government Printing 

Office, Washington, D.C. 20402. Please specify stock number 004-000-00345-4 when ordering 

copies.
Notice: The changes or modifications not expressly approved by the party responsible for 

compliance could void the user's authority to  operate the equipment.

This telephone system meets FCC standards for Hearing Aid Compatibility.

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled 

environment. This equipment should be installed and operated with a minimum distance of 20 

centimeters between the radiator and your body. This transmitter must not be co-located or 

operated in conjunction with any other antenna or transmitter.”

SEE MARKING ON BOTTOM / BACK OF PRODUCT

RISK OF ELECTRIC SHOCK

            DO NOT OPEN

WARNING: TO

PREVENT FIRE OR

ELECTRICAL SHOCK

HAZARD, DO NOT

EXPOSE THIS

PRODUCT  TO RAIN

OR MOISTURE.

THE LIGHTNING

FLASH AND ARROW

HEAD WITHIN THE

TRIANGLE IS A

WARNING SIGN

ALERTING YOU OF

“DANGEROUS

VOLTAGE” INSIDE

THE PRODUCT.

CAUTION: TO REDUCE THE

RISK OF ELECTRIC SHOCK, DO

NOT REMOVE COVER (OR

BACK). NO USER

SERVICEABLE PARTS INSIDE.

REFER SERVICING TO

QUALIFIED SERVICE

PERSONNEL.

THE EXCLAMATION

POINT WITHIN THE

TRIANGLE IS A

WARNING SIGN

ALERTING YOU  OF

IMPORTANT

INSTRUCTIONS

ACCOMPANYING

THE PRODUCT.

Make sure your package includes the items shown here.

1. Locate battery and battery door which are packaged together inside a plastic bag 

and are separate from the handset.

2. Locate the battery compartment on the back of the handset.
3. Plug the battery pack cord into the jack inside  the compartment.

YOU MUST REGISTER THE HANDSET TO THE MAIN BASE BEFORE USE!
After the optional handset has charged for 12 hours on the extra charger, 

NEEDS REGISTRATION shows in the display.
1. Press the menu ok/mute button. 

HANDSET MENU OK shows in the display. (Your handset should be held near the 

base during registration process.)

2. Press and hold the page button on the base unit until the in use indicator flashes.  

Press the handset the menu ok/mute button. 

REGISTERING shows in the display. 

HANDSET X REGISTERED shows in the handset display, where X is the handset 

number. You may now rename your handset.

1. Use the touch-tone pad to enter a name (up to 15 characters).

2. Press the menu ok/mute button to save your name. You will hear a confirmation 

tone and the handset name shows in the display.

From the Handset Setup Menu:
1.  Press the vol/CID ( 6 or 5) button to scroll to the 

DEREGISTRATION sub-menu.

2. Press the menu ok/mute button to enter the menu. 

4

2NO shows in the display The default setting is 2NO.

3.  Use the touch-tone pad to select 1 for YES or 2 for NO. Or use the vol/CID  

( 6 or 5) button to scroll to 

1YES or 2NO.

4. Select NO, if you do not want to de-register.
5. If you select YES, press the menu ok/mute button and 

MOVE NEAR TO BASE 

displays for 2 seconds, then 

CONFIRM? 1YES 2NO appears in the display.

6.  Press the touch-tone pad to select 1 for YES or 2 for NO, or use the vol/CID ( 6 or 

5

) button to scroll to 

1YES or 2NO.

7. If you select YES, press the menu ok/mute button to confirm. 

shows in the display. You will hear a confirmation tone. Then 

DEREGISTERED shows in the display to confirm the handset is deregistered.
NOTE: When you complete the de-registration process, HANDSET  

NEEDS REGISTRATION shows in the display. To use the handset,  

If one or more handsets becomes lost, you should de-register all handsets to ensure 

proper system operation. Follow the steps below to de-register all handsets at the 

same time.

1. Disconnect power from the base by pulling the plug out of the back of the unit.
2. Press and hold the page button and while holding the page button reconnect the 

power.

3. Continue to hold the page button until the in use indicator flashes rapidly.
4. Release the page button.
5. Press and release the page button on the base once. All handsets are de-

registered and 

HANDSET NEEDS REGISTRATION shows in the display.

The intercom feature allows you to have a conversation with another registered 

handset without tying up the telephone line, allowing you to still receive incoming 

calls.

1. Make sure the handset is 

OFF (not in talk mode).

2.  Press the del/conf/intercom button on the handset.
3.  Use the touch-tone pad to select the handset you want to page.

4. Wait for the person at the receiving handset to press the del/conf/intercom button.

NO ANSWER.

5. When finished, press the end button or del/conf/intercom button on either 

handset to deactivate the intercom.
NOTE: The system is expandable up to 6 handsets (by purchase of 

When you receive an intercom call, your handset beeps. To answer the call press the 

del/conf/intercom button, talk or speaker button.

If you receive a telephone call during an intercom call, the intercom call is 

immediately terminated and both handsets ring. Either handset user may press the 

talk or speaker button to answer the call.

During a telephone call, you may use the intercom/paging function to page another 

handset and have an off line, private (two-way) intercom conversation. You may also 

have a three-way conversation between the external caller and the handsets, or you 

may transfer the external telephone call to another handset.

1. During an external call, press the del/conf/intercom button, and use the touch-

tone pad to enter the handset number you want to call.
NOTE: The receiving handset presses the del/conf/intercom button to 

2. When finished, press the end button to end the intercom call, return to the talk 

mode, and resume your original telephone conversation.

1. During an external call, press the del/conf/intercom button. 

EXTENSION? shows in the display.

2. Use the touch-tone pad to select Handset #. You will hear a paging tone and 

PAGING shows in the originating handset’s display.
NOTE: PAGING FROM... shows in the display on the receiving handset, 

3. When the receiving handset connects, press the del/conf/intercom button 

on the originating handset to conference with the receiving handset and 

the external caller. 

CONFERENCE shows in the display on the originating and 

receiving handsets.
NOTE: A handset can enter conference mode directly by pressing talk or 

•  Do not burn, disassemble, mutilate, or puncture. Like other batteries of this type, 

toxic materials could be released which can cause injury.

•  To reduce the risk of fire or personal injury, use only the 

Lithium battery listed 

in the User’s Guide.

•  Keep batteries out of the reach of children.
•  Remove batteries if storing over 30 days.

If trouble is experienced with this equipment, for repair or warranty information, please 

contact customer service at 1-800-448-0329. If the equipment is causing harm to the 

telephone network, the telephone company may request that you disconnect the equipment 

until the problem is resolved.
This product may be serviced only by the manufacturer or its authorized service agents. 

Changes or modifications not expressly approved by Thomson Inc. could void the user’s 

authority to operate this product. For instructions on how to obtain service, refer to the 

warranty included in this guide or call customer service at 1-800-448-0329.
Or refer inquiries to:
Thomson Inc. 

Manager, Consumer Relations 

P O Box 1976 

Indianapolis, IN 46206
Attach your sales receipt to the booklet for future reference or jot down the date this product 

was purchased or received as a gift. This information will be valuable if service should be 

required during the warranty period.
Purchase date _________________________________________
Name of store _________________________________________

4. Insert the battery pack.
5. Close the battery compartment by pushing the door up until it snaps into place.

1. Plug the AC power converter of the extra charging cradle into the electrical outlet.

2. Place the handset in the extra charging cradle. The charge indicator turns on, 

verifying the battery is charging. 

3. Allow the phone to

 charge for 12 hours prior to first use.