Clarion DB156 安装指导

/ !

!

!

!

!

===== 

 

 

 

 

1. This set is exclusively for use in cars with a

negative ground, 12 V power supply.

2. Read these instructions carefully.

3. Be sure to disconnect the battery “

v” terminal

before starting. This is to prevent short circuits
during installation. (Figure 1)

1.

!"#$%&'12V !"#$%

2.

!"#$%&'

3.

!"#$%&'()v !"#

!"#$%&'(1F

Car battery

డӡ׏Ԅ

차 배터리

2004/12 (AB·C)

■ Fixed Mount

This unit is designed for fixed installation in the dashboard.
If the vehicle is equipped with a factory-installed radio, install the source
unit with the parts and screws marked (*) (Figure 7).
If the vehicle is not equipped with a factory-installed radio, obtain an
installation kit to install the source unit in the following procedure.

Bend the stopper following the procedures below when this source unit
is installed to the TOYOTA, NISSAN and other ISO/DIN equipped
vehicles.

1. Bend the stopper from the source unit. (Figure 5, 6)

■ 

=====

E

E

E

E

E

 

 

 

 

 I=

I=

I=

I=

I=

===== 

 

 

 

 =fplLafk=

=fplLafk=

=fplLafk=

=fplLafk=

=fplLafk=

 

 

 

 

 =====

===== 

 

 

 

 FFFFF

== !== = = = !"K

== = != = !I=EGF====

= = = !"#=ETFK

= = != !== !I== = 

 == = = !"#K

 I== =fplLafk= == != = 

 = = == != !"#K

NK=

 = != !"K=E=RI=SF

■  !

!"#$%&'(fplLafk !

!"#$%&'()*+

!"#$%&'(")*+,-./0123EGF !"#$

!"#T

!"#$%&'(#)*+,-./0(#12345678(#

!"

!"#$%&'()*+,-fplLafk !"#$%&'()

!"#
NK

!"#$%&'(RS

■ Universal Mount

1. Place the universal mounting bracket into the instrument panel, use a

screwdriver to bend each stopper of the universal mounting bracket
inward, t-hen secure the stopper as shown in Figure 4.

2. Wire as shown in Section 8.

3. Insert the source unit into the universal mounting bracket until it

locks.

4. Take care of the top and bottom of the outer escutcheon and mount it

so that all the hooks are locked.

■  !"#

1.

!"#$%&'()*+ ,-. !"#$/0123

!"#$%&'4 !"#$%

2.

8 !"#$

3.

!"#$%&!'()*+,-./

4.

!"#$%&'(&)*+,-.$/012345

■ =

1.

= = != ==I= !"== 

!= !== != !==4==

= != !"#K

2.

=8= === = K

3.

 == !== = !K

4.

= !== = != == != !

K

(182 mm)

Outer escutcheon

ບ૲আ

외부 프레임

Instrument panel

ၕѝϷ

계기반

Hole

ा५

홀

Hexagonal bolt

੉࢟ઋඤ

육각형 볼트

Stoppers

ᇌ׵ఝ

스토퍼

Stoppers

ᇌ׵ఝ

스토퍼

Screwdriver

ઋර֞

드라이버

Universal mounting bracket 

๠Ⴏሔ஬ᆭࡖ 

일반 탑재용 받침대

Strap

༵๏

스트랩

* 

This part is not provided in some models.

* 

Օਲ਼ࡸᄤႼཻࠖྟેႼ฻܉è

* 

이 부품은 일부 모델에는 제공되지 않습니다.

ႂჾሔᇉ

본체

६ᇌขा५ԋձ

콘솔 입구 크기

Hole

ा५

홀

53 mm

Note:
Before attaching the universal mounting bracket, slightly bend 
the spring toward the inside with your fingers and attach it to the 
side of car.

ሆĈ
τሔ๠Ⴏሔ஬ᆭࡖᆴఴƗ౯Ⴏ൴ᆾࢃ֗ߥഔསୄҮຜƗࢃఊτሔ
ᄤడӡ၉Үè

주:

일반 탑재용 받침대를 부착시키기 전에, 스프링을 손가락으로 

약간 안쪽으로 구부린 다음 차 쪽으로 부착시키십시오.

Top

׫ҍ

위

Bottom

ֿҍ

아래

Installation direction

τሔ١ས

설치 방향

ບ૲আҮ൱๴

외부 프레임을 옆에서 본 그림

1. Prepare all articles necessary for installing the source unit before

starting.

2. Install the unit within 30° of the horizontal plane. (Figure 2)

3. If you have to do any work on the car body, such as drilling holes,

consult your car dealer beforehand.

4. Use the enclosed screws for installation. Using other screws can

cause damage. (Figure 3)

1.

!"#$%&'()*(+,-./0123

2.

!"#$%&'()*+,-30° E2F

3.

!"#$%&'()*+,-.,/01#234567

4.

!"#$%&'()* +,$%-./012*E3F

OK=

=T===== != = !"#K

!== !"#= === !K==

= !=I== ==== != =

== !K

PK=

=U= === = K

QK=

!= = !=I= !== ==

!K

Notes:
1) Some car models require special mounting kits for proper

installation. Consult your Clarion dealer for details.

2) Fasten the front stopper securely to prevent the source unit from

coming loose.

1)

!"#$%&'()*+,-.&/012345Clarion

!"

2)

!"#$%&'()*"+

WWWWW
1)

= =I= = = = == =

== !K= ==`ä~êáçå= = !"#K

2)

 = !== != = !"==

!K

ᇖရϷሆ 1

센터 패널 (주 1)

๴ 7

그림 7

ႂჾሔᇉ

본체

Mounting bracket 

*

 

(1 pair for the left and right sides)

ሔ஬ᆭࡖ 

*

 

၉ؚႯ჆቗Ⴞ਍Ү

탑재 받침대 

*

  

(왼쪽과 오른쪽의 한짝)

ၕѝϷ

계기반

Pocket

३ގ

포켓

★

★

★

★

★

4–Hexagonal screw 

*

 (M5 

×

 8)

4

۸੉࢟ઋර 

*

 (M5 

×

 8)

4

개의 육각형 나사 

*

 

(M5 

×

 8

)

ሆ 2 

주 2

★

∗ : The parts and screws with this mark are used to install radio or
included in the installation kit.

★: The screws with this mark are originally attached to the vehicle.

Note 1: In some cases, the center panel may require some modification

(trimming, filling, etc.).

Note 2: If a hook on the installation bracket interferes with the unit, bend

and flatten it with a nipper or a similar tool.

∗ :

!"#$%&'()*+,-./012*+3456

★:  !"#$%&'()"*

!"#$%&'()*+,-.E !"#F

!"#$%&'()*!+,-./0123456789

 

∗ :

= = = = = = = !I==

= != !K

★: = = = = != != !== 

K

=====1 :  = == == = = !K=E

I==F

=====2 : = === = =I= ==

= != != !K

1.

= =12VI=åÉÖ~íáîÉ=ÖêçìåÇ=

 == = !"K

2.

= !"#=== !"#K

3.

!= = !=“v”= =

!K= = = = !=

= K=E=1F

Max. 8 mm /

 

ቒս

 

8

 

mm 

/ 

최대 8 mm

Chassis / 

ֿஔ 

/ 

차대

Chassis / 

ֿஔ 

/ 

차대

Damage / 

෬ߑ 

/ 

손상

Max. 30˚ / 

ቒս

 

30˚

 / 

최대 30˚

1.

!== = = == !"#K

2.

 = !=30°= = !"#K=E=2F

3.

 = ==== = =I= ==

= !"#K

4.

 = = != !"#K== = !=

= === !K=E=3F

1. When removing the source unit, disassemble it in the reverse of

the order in Section “3. INSTALLING THE SOURCE UNIT”.

2. Press the outer escutcheon upward and remove it. (Figure 8)

3. Insert and lock the hook plates. (Figure 9)

4. Pull the hook plates to remove the source unit.

1.

!"#$%&'()33.

 

!"#$%&'()

 

2.

!"#$%&'()* 8

3.

!"#$%&= 9

4.

!"#$%&'()*

๴ 8

그림 8

2–Hook plate

2

۸ܲܓϷ

2

개의 훅 플레이트

Outer escutcheon

ບᅾ

외부 프레임

๴ 9

그림 9

=====4

!

!

!

!

!

 

 

 

 

 

 

 

 

 

 

!"

=====

!"#$%

!"#$%

!"#$%

!"#$%

!"#$%

 

 

 

 

 ===== !

!

!

!

!

 

 

 

 

 

 

 

 

 

 

1.

 = =I==“3. =”== != !

K

2.

= != != = !"K=E 8F

3.

= !"== !K=E 9F

4.

= !"= = = !"K

 

 

 

 

 

!"#

!"#

!"#

!"#

!"#

=====

STOPPER/

制动器

/

스토퍼

SOURCE UNIT/

主机

/

본체

弯曲前

구부리기 전

AFTER BEND/弯曲后/

구부린 후

图 5

그림 5

图 6

그림 6

2. Secure the mounting brackets to the chassis as shown in Figure 7.

Holes are pre-tapped for TOYOTA and NISSAN vehicles; modifica-
tion, such as drilling new holes, of the mounting brackets may be
required for other models.

3. Wire as shown in Section 8.

4. Secure the unit in the dashboard, and then reassemble the dash-

board and the center panel.

OK

T !"#$%&'()*+,-./012345678"

!"#$%&'()*+,-./012345

PK

U !"#$

QK

!"#$%&'()*+,-. %&'/01'2