ICOM IC-706MKIIG 用户手册
17
3
FREQUENCY SETTING
• P
Prro
og
grra
am
mm
ma
ab
blle
e ttu
un
niin
ng
g s
stte
ep
ps
s
Programmable tuning steps are available to suit your
operating requirements.
These tuning steps are:
• Independently selectable for each mode
• Selectable from 0.01 (FM/WFM/AM only), 0.1, 1, 5,
operating requirements.
These tuning steps are:
• Independently selectable for each mode
• Selectable from 0.01 (FM/WFM/AM only), 0.1, 1, 5,
9, 10, 12.5, 15, 20 and 100 kHz
➀
Push [TS] one or more times until the programma-
ble tuning step indicator, “
ble tuning step indicator, “
Z
,” appears above the
1 kHz digit.
• Rotating the main dial changes the frequency accord-
ing to the set tuning step.
➁
Push [TS] for 2 sec. while the programmable tun-
ing step indicator appears to enter the tuning step
selection mode.
ing step indicator appears to enter the tuning step
selection mode.
• Rotate DIAL appears.
➂
Rotate the main dial to set the desired tuning step.
• Change the mode and select tuning steps for other
modes, if desired.
➃
Push [TS] to exit the tuning step selection mode.
➄
Rotate the main dial to change the frequency
according to the set tuning step.
according to the set tuning step.
• B
Ba
an
nd
d s
se
elle
ec
cttiio
on
n
All HF ham bands, the 50 MHz band, the 144 MHz
band and a general coverage receiver band are
included in the IC-706MKIIG.
band and a general coverage receiver band are
included in the IC-706MKIIG.
Push [
(Y)
BAND]/[
(Z)
BAND] to select the desired
band.
• Pushing [
(Y)
BAND]/[
(Z)
BAND] continuously scrolls
through the available bands.
N
No
otte
e:: The band stacking register can also be used to
select bands. Refer to p. 19.
USB
FM
USB
USB
LSB
Z
Z
■ FFrreeqquueennccyy sseettttiinngg
Programmable tuning
step indicator
step indicator
10 kHz tuning step is
selected for USB
operation.
selected for USB
operation.
CH
VFO A
P
O
S1
5
5
3
7
9
20
40
10
60dB
USB
USB
M1
A/B A=B
DIAL
SPL
Rotate
• 1
1 H
Hz
z a
an
nd
d 1
10
0 H
Hz
z ttu
un
niin
ng
g s
stte
ep
ps
s
When neither the quick tuning step or programmable
tuning step, “
tuning step, “
Z
,” appear, rotating the main dial
changes the frequency in increments of 1 or 10 Hz.
These tuning steps are only available in SSB, CW
and RTTY modes.
These tuning steps are only available in SSB, CW
and RTTY modes.
➀
Select SSB, CW or RTTY mode if necessary.
➁
Push [TS] for 2 sec. to toggle between the 1 and
10 Hz step settings.
10 Hz step settings.
• When the 1 Hz step is selected, the 1 Hz digit appears
in the frequency indication; when the 10 Hz step is
selected, the 1 Hz digit disappears from the frequency
indication.
selected, the 1 Hz digit disappears from the frequency
indication.
Rotating the main dial
changes the frequency
in 10 Hz steps.
changes the frequency
in 10 Hz steps.
Rotating the main dial
changes the frequency
in 1 Hz steps.
changes the frequency
in 1 Hz steps.
TS
Push
for 2 sec.
VFO A
USB
VFO A
USB
IC-706MKIIG.qxd 02.3.27 13:53 Page 17