Husqvarna 532 43 14-90 yth2348 用户手册
22
SERVICE AND ADJUSTMENTS
FIG. 31
RE TAIN ING
RING
RING
WASH ERS
SQUARE KEY (REAR
WHEEL ONLY)
WHEEL ONLY)
AXLE COVER
TO START ENGINE WITH A WEAK BATTERY
(See Fig. 32)
(See Fig. 32)
WARNING: Lead-acid batteries gen-
er ate ex plo sive gases. Keep sparks,
fl ame and smoking ma te ri als away from
bat ter ies. Always wear eye pro tec tion
when around batteries.
er ate ex plo sive gases. Keep sparks,
fl ame and smoking ma te ri als away from
bat ter ies. Always wear eye pro tec tion
when around batteries.
If your battery is too weak to start the engine, it should be
recharged. (See "BATTERY" in the MAINTENANCE sec-
tion of this man u al).
If “jumper ca bles” are used for emer gen cy starting, follow
this pro ce dure:
recharged. (See "BATTERY" in the MAINTENANCE sec-
tion of this man u al).
If “jumper ca bles” are used for emer gen cy starting, follow
this pro ce dure:
IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT
SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT
SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START
OTHER VEHICLES.
SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT
SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START
OTHER VEHICLES.
TO ATTACH JUMPER CABLES -
• Connect one end of the RED cable to the POSITIVE
• Connect one end of the RED cable to the POSITIVE
(+) terminal of each battery(A-B), taking care not to
short against tractor chassis.
short against tractor chassis.
•
Connect one end of the BLACK ca ble to the NEGA TIVE
(-) terminal (C) of fully charged battery.
(-) terminal (C) of fully charged battery.
•
Connect the other end of the BLACK cable (D) to good
chassis ground, away from fuel tank and bat tery.
chassis ground, away from fuel tank and bat tery.
TO REMOVE CABLES, REVERSE ORDER -
•
•
BLACK cable fi rst from chassis and then from the fully
charged battery.
charged battery.
• RED cable last from both batteries.
FIG. 32
WEAK OR DEAD
BATTERY
BATTERY
FULLY CHARGED
BATTERY
BATTERY
REPLACING BATTERY (See Fig. 33)
WARNING: Do not short battery ter mi nals by allowing
a wrench or any other object to contact both terminals at
the same time. Before connecting battery, remove metal
bracelets, wristwatch bands, rings, etc.
the same time. Before connecting battery, remove metal
bracelets, wristwatch bands, rings, etc.
Positive terminal must be connected fi rst to prevent spark-
ing from ac ci den tal grounding.
•
ing from ac ci den tal grounding.
•
Lift hood to raised position.
•
Disconnect BLACK battery cable (A) then RED battery
cable and carefully remove battery from tractor.
cable and carefully remove battery from tractor.
•
Install new battery with terminals in same position as
old battery.
old battery.
•
First connect RED battery cable (B) to positive (+) battery
terminal with hex bolt and keps nut as shown. Tighten
securely. Slide terminal cover (C) over terminal.
terminal with hex bolt and keps nut as shown. Tighten
securely. Slide terminal cover (C) over terminal.
•
Connect BLACK grounding cable to negative (-) bat tery
terminal with re main ing hex bolt and keps nut. Tight en
securely
terminal with re main ing hex bolt and keps nut. Tight en
securely
• Close
hood.
Positive
(Red)
Cable
(Red)
Cable
Negative
(Black)
Cable
(Black)
Cable
02954
A
B
C
FIG. 33
•
Repair tire and reassemble.
•
On rear wheels only: align grooves in rear wheel hub
and axle. Insert square key.
and axle. Insert square key.
•
Replace washers and snap retaining ring securely in
axle groove.
axle groove.
• Replace
axle
cover.
NOTE: To seal tire punctures and prevent fl at tires due to
slow leaks, tire sealant may be purchased from your local
parts dealer. Tire sealant also prevents tire dry rot and
corrosion.
slow leaks, tire sealant may be purchased from your local
parts dealer. Tire sealant also prevents tire dry rot and
corrosion.