Orion 9825 用户手册
![Orion](https://files.manualsbrain.com/attachments/8f46860c7e16c5c7b1192bc67b9860e6d51a25cc/common/fit/150/50/929fe0db313802128f7a879b2b3455f87ace4519b865189705f50e8d9a91/brand_logo.png)
3
Getting Started
The Apex telescopes come nearly fully assembled from the
factory. The optics have been installed and collimated, so you
should not have to make any adjustments to them. Open the
box and inspect the contents to make sure all of the parts list-
ed above are present. Refer to Figure 1 to see what the parts
look like, and how they will connect togther; the Apex 102mm
is shown, but all models have similar components.
factory. The optics have been installed and collimated, so you
should not have to make any adjustments to them. Open the
box and inspect the contents to make sure all of the parts list-
ed above are present. Refer to Figure 1 to see what the parts
look like, and how they will connect togther; the Apex 102mm
is shown, but all models have similar components.
Please keep the original shipping box. In the unlikely event
you should need to ship the telescope back to Orion for war-
ranty repair service, you should use the original packaging.
The box also makes a very good container for storing the tel-
escope when it is not in use.
you should need to ship the telescope back to Orion for war-
ranty repair service, you should use the original packaging.
The box also makes a very good container for storing the tel-
escope when it is not in use.
Installing the Accessories
Apex 90mm:
To place the finder scope in the finder scope bracket, first
unthread the three alignment thumb screws on the bracket
until the screw ends are flush with the inside of the bracket’s
ring. Insert the finder scope into the bracket so that the eye-
piece end of the finder scope (the end with the rubber
eyeguard) is closest to the bracket’s alignment thumb screws
(see Figure 2). Secure the finder scope in place by tightening
the three alignment thumbscrews.
unthread the three alignment thumb screws on the bracket
until the screw ends are flush with the inside of the bracket’s
ring. Insert the finder scope into the bracket so that the eye-
piece end of the finder scope (the end with the rubber
eyeguard) is closest to the bracket’s alignment thumb screws
(see Figure 2). Secure the finder scope in place by tightening
the three alignment thumbscrews.
Apex 102mm and 127mm:
To place the finder scope in the finder scope bracket, first
unthread the two black nylon alignment screws until the screw
ends are flush with the inside of the bracket’s cylinder. Place
the O-ring that comes on the base of the bracket over the
body of the finder scope until it seats into the slot on the mid-
dle of the finder scope. Insert the eyepiece end (narrow end)
of the finder scope into the end of the bracket’s cylinder that
does not have the alignment screws, while pulling the spring-
loaded tensioner on the bracket with your fingers (see Figure
3). Push the finder scope through the bracket until the O-ring
seats just inside the front opening of the bracket’s cylinder.
Now, release the tensioner and tighten the alignment screws
a couple of turns each to secure the finder scope in place.
unthread the two black nylon alignment screws until the screw
ends are flush with the inside of the bracket’s cylinder. Place
the O-ring that comes on the base of the bracket over the
body of the finder scope until it seats into the slot on the mid-
dle of the finder scope. Insert the eyepiece end (narrow end)
of the finder scope into the end of the bracket’s cylinder that
does not have the alignment screws, while pulling the spring-
loaded tensioner on the bracket with your fingers (see Figure
3). Push the finder scope through the bracket until the O-ring
seats just inside the front opening of the bracket’s cylinder.
Now, release the tensioner and tighten the alignment screws
a couple of turns each to secure the finder scope in place.
All models:
Connect the finder scope bracket to the dovetail holder on the
optical tube with the thumb screw on the holder. Insert the 45°
diagonal into the eyepiece adapter and secure it with the
thumb screws on the eyepiece adapter. Insert an eyepiece
into the diagonal and tighten the thumb screws on the
diagonal.
optical tube with the thumb screw on the holder. Insert the 45°
diagonal into the eyepiece adapter and secure it with the
thumb screws on the eyepiece adapter. Insert an eyepiece
into the diagonal and tighten the thumb screws on the
diagonal.
Keep the dust cap over the front end of the telescope when it
is not in use. It is also a good idea to cover the eyepiece; use
the cover cap that came with it.
is not in use. It is also a good idea to cover the eyepiece; use
the cover cap that came with it.
Mounting the Telescope on a Tripod
The Apex Maksutov-Cassegrain optical tube assemblies can
be mounted on any standard camera tripod that has a 1/4"-20
stud. The stud threads into the block on the underside of the
telescope’s optical tube (see Figure 4). Alternatively, the tele-
scopes can be attached to an altazimuth or equatorial mount
equipped with a 1/4"-20 adapter. For the Apex 127mm, there
are several threaded holes in the mounting block; use the one
that will best balance the telescope on the tripod or mount.
be mounted on any standard camera tripod that has a 1/4"-20
stud. The stud threads into the block on the underside of the
telescope’s optical tube (see Figure 4). Alternatively, the tele-
scopes can be attached to an altazimuth or equatorial mount
equipped with a 1/4"-20 adapter. For the Apex 127mm, there
are several threaded holes in the mounting block; use the one
that will best balance the telescope on the tripod or mount.
Figure 2: Insert the 6x20 finder scope into the bracket’s
rings so that it is oriented as shown.
rings so that it is oriented as shown.
Finder scope eyepiece
Figure 3: To install the 6x26 finder scope in the finder
scope bracket, pull the spring-loaded tensioner while
inserting the eyepiece end of the finder scope into the
bracket.
scope bracket, pull the spring-loaded tensioner while
inserting the eyepiece end of the finder scope into the
bracket.
Spring-loaded
tensioner
Eyepiece end of
finder scope
finder scope
Alignment thumb
screw (3)
Alignment thumb screws
O-ring
Figure 4: The
1/4”-20 stud on
standard camera
tripods will
thread into the
mounting block
on the underside
of the Apex
telescopes. The
Orion Paragon
HD-F2 tripod
shown utilizes a
quick-release
shoe to connect
the telescope to
the tripod.
1/4”-20 stud on
standard camera
tripods will
thread into the
mounting block
on the underside
of the Apex
telescopes. The
Orion Paragon
HD-F2 tripod
shown utilizes a
quick-release
shoe to connect
the telescope to
the tripod.
1/4”-20 stud
Mounting block