Rowenta dx6000 用户手册
Selecting the Temperature
Set the temperature control dial according
to the fabric you are ironing. Check the gar-
ments label for appropriate setting.
We recommend using the chart below as a
guide.
to the fabric you are ironing. Check the gar-
ments label for appropriate setting.
We recommend using the chart below as a
guide.
Light will be on as iron is heating. When light goes out iron
is ready to use. When heating a cold iron, please allow
thermostat to cycle twice before use (thermostat light will
go on and off twice).
is ready to use. When heating a cold iron, please allow
thermostat to cycle twice before use (thermostat light will
go on and off twice).
Steam ironing
Warning!
Never iron or steam clothes while they are being worn.
Never iron or steam clothes while they are being worn.
Before ironing for the first time fill iron and allow to heat.
The iron should be allowed to emit steam for 1 to 2 minu-
tes while pressing the burst of steam button a few times
to remove any impurities. This should also be done if iron
is not used regularly.
The iron should be allowed to emit steam for 1 to 2 minu-
tes while pressing the burst of steam button a few times
to remove any impurities. This should also be done if iron
is not used regularly.
Steam is only produced when the temperature dial is set to
the shaded area (after •• setting).
the shaded area (after •• setting).
Variable Steam
Maximum steam setting should only be
used when the iron is set to the highest
temperature setting (•••) . Steam will be pro-
duced when iron is used horizontally.
Maximum steam setting should only be
used when the iron is set to the highest
temperature setting (•••) . Steam will be pro-
duced when iron is used horizontally.
Burst of steam
This feature is ideal for removing stubborn
wrinkles or pressing in sharp creases in
horizontal use. When the temperature con-
trol is set to the steam zone (after ••) the
burst of steam can be used by pressing the
burst of steam button. Leave an interval of
4 seconds between bursts.
This feature is ideal for removing stubborn
wrinkles or pressing in sharp creases in
horizontal use. When the temperature con-
trol is set to the steam zone (after ••) the
burst of steam can be used by pressing the
burst of steam button. Leave an interval of
4 seconds between bursts.
Filling with water
•
Ensure the iron is unplugged.
•
Slide the variable steam lever to the left (
).
•
Rest the iron on heel and tilt it forward
approximately 1 inch. If the iron is equip-
ped with a covered filling inlet, open the
filling inlet by sliding the cover down.
approximately 1 inch. If the iron is equip-
ped with a covered filling inlet, open the
filling inlet by sliding the cover down.
•
Fill with water (containing no additives) to
the max mark on the water tank. We
recommend using a water pitcher rather
than filling under the tap.
the max mark on the water tank. We
recommend using a water pitcher rather
than filling under the tap.
•
If equipped with filling inlet cover, slide
cover to close.
cover to close.
If you need to add water during ironing,
UNPLUG the iron and follow the steps above.
Ensure iron heats back to temperature after-
wards, that means thermostat light will go out.
UNPLUG the iron and follow the steps above.
Ensure iron heats back to temperature after-
wards, that means thermostat light will go out.
Water Recommendations
Tap water
Rowenta irons are designed to be used with REGULAR TAP
WATER (up to 12 grains of hardness). If your water is harder
than this, Rowenta recommends mixing half tap water with
half distilled water which reduces the hardness; or just use
bottled spring water. Never use 100 % distilled water as
this can cause the iron to spit and leak.
Rowenta irons are designed to be used with REGULAR TAP
WATER (up to 12 grains of hardness). If your water is harder
than this, Rowenta recommends mixing half tap water with
half distilled water which reduces the hardness; or just use
bottled spring water. Never use 100 % distilled water as
this can cause the iron to spit and leak.
Softened water
There are many types of household water softeners and the
water from many of them is perfectly acceptable for use in
an iron. However, some types of softeners, particularly those
that use chemicals such as salt, can cause the appliance to
leak or spit during use. If you experience this type of problem,
we recommend that you try using bottled spring water or
untreated tap water. Never use 100 % distilled water.
There are many types of household water softeners and the
water from many of them is perfectly acceptable for use in
an iron. However, some types of softeners, particularly those
that use chemicals such as salt, can cause the appliance to
leak or spit during use. If you experience this type of problem,
we recommend that you try using bottled spring water or
untreated tap water. Never use 100 % distilled water.
Once you have changed water it will take several uses to
correct the problem. Rowenta recommends trying the
steam function for the first time on an old towel or cloth
that can be discarded to avoid damaging your clothes.
correct the problem. Rowenta recommends trying the
steam function for the first time on an old towel or cloth
that can be discarded to avoid damaging your clothes.
Iron and other impurities
If your water supply contains large amounts of iron or
organic matter, these minerals can collect inside the
appliance and eventually appear as brown stains. If you
experience these problems Rowenta recommends using
bottled spring water. Never use 100 % pure distilled water.
If your water supply contains large amounts of iron or
organic matter, these minerals can collect inside the
appliance and eventually appear as brown stains. If you
experience these problems Rowenta recommends using
bottled spring water. Never use 100 % pure distilled water.
Always remember:
Battery water and water containing additives (such as
starch, perfume or fabric conditioner condensed water
from driers) may not be used. Such additives can affect the
properties of the steam and, at high temperatures, can
form deposits in the steam chamber, which will mark the
laundry when they are emitted through the steam vents.
Descaling liquids / agents should not be used.
starch, perfume or fabric conditioner condensed water
from driers) may not be used. Such additives can affect the
properties of the steam and, at high temperatures, can
form deposits in the steam chamber, which will mark the
laundry when they are emitted through the steam vents.
Descaling liquids / agents should not be used.
PRO Vertical Steam (depending on model)
To be used at maximum temperature setting
••• . This feature generates a powerful
vertical steam and is ideal for removing
creases from hanging clothes (e.g. suits,
jackets, shirts), hanging curtains etc.
••• . This feature generates a powerful
vertical steam and is ideal for removing
creases from hanging clothes (e.g. suits,
jackets, shirts), hanging curtains etc.
•
Hang up garment on a hanger.
•
Set the variable steam control to
position.
position.
•
Hold the iron a few inches away from the
garment to avoid burning delicate fabrics.
garment to avoid burning delicate fabrics.
•
Press the PRO Vertical Steam button every
2 seconds to generate a steady flow of steam.
2 seconds to generate a steady flow of steam.
•
Moving the iron from top to bottom.
When using PRO Vertical Steam, we recommend periodi-
cally placing the iron down to allow it to reheat.
Before placing the iron on its heel, wait for the steam flow
to finish. As the steam is very hot in the beginning it will be
not visible. You will hear the steam function engage and
after few bursts it will be visable.
cally placing the iron down to allow it to reheat.
Before placing the iron on its heel, wait for the steam flow
to finish. As the steam is very hot in the beginning it will be
not visible. You will hear the steam function engage and
after few bursts it will be visable.
Warning! Never direct the steam jet at persons or animals.
Dry ironing
To iron without steam, slide the variable steam control
lever to the
lever to the
position. We recommend dry ironing with
an empty tank. Set the temperature for the type of material
to be ironed (•, •• or •••).
to be ironed (•, •• or •••).
Spray setting
This feature is ideal for stubborn wrinkles or
set in creases.
Ensure there is water in the tank then press
the spray button.
Do not spray silk.
set in creases.
Ensure there is water in the tank then press
the spray button.
Do not spray silk.
Anti-Drip System (depending on model)
In order to produce steam, all irons require a high
temperature. If the soleplate is not hot enough some of the
water will not turn to steam and can spit or leak from the
soleplate. The Anti-Drip system automatically switches off
the steam when ironing at low temperatures to prevent
spitting.
temperature. If the soleplate is not hot enough some of the
water will not turn to steam and can spit or leak from the
soleplate. The Anti-Drip system automatically switches off
the steam when ironing at low temperatures to prevent
spitting.
Self Clean
Warning! Do not use descaling agents. They can damage
the lining of the steam chamber.
the lining of the steam chamber.
This feature allows loose mineral deposits and other impu-
rities to be flushed from the soleplate.
rities to be flushed from the soleplate.
Self Clean should be carried out occasionally and at least
once a month.
once a month.
Before use
•
Remove soleplate cover before using iron.
•
Remove all packaging from the iron.
•
Please read all of the Instructions for Use
and the Important Safety Guards carefully.
and the Important Safety Guards carefully.
•
It is normal for a small amount of smoke
and a light odor to be produced the first
time it is used. This will quickly disappear.
and a light odor to be produced the first
time it is used. This will quickly disappear.
•
Particles may emit from iron during first
use. They are not harmful and should
disappear after the iron has been allowed
to steam.
use. They are not harmful and should
disappear after the iron has been allowed
to steam.
Helpful Hints
•
When ironing, start with fabrics that require a low
temperature setting (•) and finish with those which need
the highest temperature (•••).
temperature setting (•) and finish with those which need
the highest temperature (•••).
•
Mixed fiber fabrics should be ironed on the temperature
for the most delicate fabrics. For example a shirt that is
60% cotton and 40% polyester should be ironed at the (•)
setting for synthetics.
for the most delicate fabrics. For example a shirt that is
60% cotton and 40% polyester should be ironed at the (•)
setting for synthetics.
•
If spray starch is used, spray it onto the reverse side of
the garment. Allow starch to penetrate before ironing by
setting garment aside for 30 seconds.
the garment. Allow starch to penetrate before ironing by
setting garment aside for 30 seconds.
•
For best results, use a mesh type ironing board to allow
excess steam to escape.
excess steam to escape.
•
For delicate fabrics, we recommend carrying out a test on
an unobtrusive area of the garment such as an inner
seam.
an unobtrusive area of the garment such as an inner
seam.
•
Adhere to manufacturer recommendations on garment
label.
label.
3 Way Auto-Off (depending on model)
If your iron is equipped with auto-off and
the iron is not moved while it is plugged in,
an internal safety switch will turn it off. It
will turn off in 8 minutes if left vertically or
in 30 seconds if left on its soleplate or tip-
ped over.
The auto-off light will remain on and lit
during ironing.
the iron is not moved while it is plugged in,
an internal safety switch will turn it off. It
will turn off in 8 minutes if left vertically or
in 30 seconds if left on its soleplate or tip-
ped over.
The auto-off light will remain on and lit
during ironing.
The light will flash when the auto-off feature has engaged.
To deactivate feature, move the iron or shake it gently.
Wait until iron is fully reheated before use.
To deactivate feature, move the iron or shake it gently.
Wait until iron is fully reheated before use.
Auto off is not an on/off switch. Always unplug the iron
when not in use.
when not in use.
IMPORTANT SAFETY INSTRUCTIONS
When using this appliance, basic safety precautions should
always be followed including the following:
always be followed including the following:
Read all instructions before using this product.
•
Use appliance only for its intended use.
•
To protect against a risk of electric shock, do not immerse
the appliance in water or other liquids.
the appliance in water or other liquids.
•
The appliance should always be turned off before plugging
or unplugging from outlet. Never yank the cord to disconnect
from outlet, instead grasp plug and pull to disconnect.
or unplugging from outlet. Never yank the cord to disconnect
from outlet, instead grasp plug and pull to disconnect.
•
Always disconnect appliance from electrical outlet when
filling with water or emptying when not in use.
filling with water or emptying when not in use.
•
Do not allow cord to touch hot surfaces. Let iron cool
completely before putting away. Loop cord loosely around
iron when storing.
completely before putting away. Loop cord loosely around
iron when storing.
•
Do not operate appliance with a damaged cord or if
appliance has been dropped or damaged.
appliance has been dropped or damaged.
•
To avoid the risk of electric shock, do not disassemble the
appliance. Ship it to the nearest authorized Rowenta
approved service center for examination and repair.
Incorrect reassembly can cause a risk of electric shock
when the appliance is used.
appliance. Ship it to the nearest authorized Rowenta
approved service center for examination and repair.
Incorrect reassembly can cause a risk of electric shock
when the appliance is used.
•
Not intended for use by children. Close supervision is
necessary for any appliance being used near children.
Unsupervised use can result in fire or personal injury.
Do not leave appliance unattended while plugged in,
on an ironing board, or while it is still hot.
necessary for any appliance being used near children.
Unsupervised use can result in fire or personal injury.
Do not leave appliance unattended while plugged in,
on an ironing board, or while it is still hot.
•
Burns can occur from touching hot metal parts, hot water or
steam. Use caution when you turn a steam iron upside
down. There may be hot water in the reservoir.
steam. Use caution when you turn a steam iron upside
down. There may be hot water in the reservoir.
•
Do not direct steam at people, animals or iron clothes while
they are being worn.
they are being worn.
•
The use of accessory attachments is not recommended by
Rowenta and may result in fire, electric shock or personal
injury.
Rowenta and may result in fire, electric shock or personal
injury.
SPECIAL INSTRUCTIONS
SAVE THESE INSTRUCTIONS
•
This is a 1400/1500 watt appliance. To avoid a circuit overload,
do not operate a high wattage appliance on the same circuit.
do not operate a high wattage appliance on the same circuit.
•
If an extension cord is absolutely necessary, the marked
electrical rating should be at least as great as the electrical
rating of the appliance. Cords rated for less amperage may
overheat. Care should be taken to arrange the cord so that it
cannot be pulled or tripped over unintentionally.
electrical rating should be at least as great as the electrical
rating of the appliance. Cords rated for less amperage may
overheat. Care should be taken to arrange the cord so that it
cannot be pulled or tripped over unintentionally.
•
Your Rowenta appliance is intended for household use only.
30 sec. 8 min.
SELF
CLEAN
CLEAN
Ironing label
Fabric
Synthetics e.g.
polyester, silk, viscose
Wool
Cotton, linen
Temperature control
DX6000_USA 18.11.2003 11:29 Uhr Seite 2