Korg triton-rack 信息指南

Here’s how to load demo multisample data and play it 
back in Sampling mode.

1 Load “DCUT_SMP.KSC” from the included 

1) Insert the included “TNRFD-01P” floppy disk 

into the floppy disk drive.

2) Press the [DISK] key (LED lit) to enter Disk 

mode.

3) Press the [F1] (“Load”) key to select the Load 

page.

4) Use the [

], [

] keys to select 

“DCUT_SMP.KSC”

5) Press the [F8] (“UTILITY”) key to access the util-

ity menu.

6) Press the [F7] key to choose “Load Selected,” and 

press the [F8] (“OK”) key. The following dialog 
box will appear.

7) For this example, select Clear for “.KSC Alloca-

tion”

When you select Clear and then load, the multi-
sample data and sample data of Sampling mode 
will be erased (

8) Press the [F8] (“OK”) key to load the data.

Never remove the media while data is being 
loaded.

2 Make sure that multisample 000: Gospel Vocal L is 

1) Press the [SAMPLING] key (LED lit) to enter 

Sampling mode.

2) If SMPL 1.1: Recording is not selected, press the 

[EXIT] key.

3) Press the [F1] (“Sample”) key to select the Sam-

ple page.

4) If 000: Gospel Vocal L is not selected, use the [

], 

[

], [

], [

] keys to choose “Multisample 

Select,” and use the [INC], [DEC] keys to select it.

3 Set the channel of the transmitting MIDI device to 

With the factory settings, the global MIDI channel is 
set to channel 1. Set the transmitting MIDI device to 
MIDI channel 1.

4 Play the samples of the multisample.

For example if the transmitting MIDI device is a 
MIDI keyboard, play any note in the range of C2, 
D2–F#2 to sound the sample that is assigned to that 
key.
You can also press the [AUDITION] key to hear the 
sample played. For “Index,” use the [INC][DEC] 
keys to select another sample for assignment to the 
multisample, and press the [AUDITION] key.

Multisample data you sampled in Sampling mode or 
sample/multisample data you loaded in Disk mode 
can be converted to a program by executing the “Conv. 
To Prog” utility. (

Alternatively, a multisample you created in Sampling 
mode can be assigned to the Program mode parame-
ters “High MS Bank” and “High Multisample” or 
“Low MS Bank” and “Low Multisample,” and used as 
a program.

When a multisample you created in Sampling mode is 
used as a program, you will be able to process its 
sound in various ways by using the filter and effects of 
the program.

By selecting the preloaded program I-E 000: Sampler 
Waves

, you can listen to the various samples of a pro-

gram that uses the multisample you heard in step 4. 
You can hear the result of using the compressor or 
delay etc. to process the sound of the multisample.

Samples can be used in a drum kit. 

The multisamples and samples of Sampling mode 
will disappear when the power is turned off. If 
you wish to use them after turning the power on 
once again, you must reload them.

Here’s how you can use Sampling mode to sample a 
drum phrase from an audio CD etc., and convert it into 
a program.

You will need to provide a rhythm loop sample such as 
a drum phrase from a CD or other audio source. To 
start with, let’s use a rhythm loop sample with a rela-
tively simple beat.

As an example here, we will sample two one-measure 
drum phrases in 4/4 time at 140 BPM and 100 BPM.