Intermatic t101 用户手册
MODEL: T101
24 HOUR DIAL TIME SWITCH
SINGLE POLE SINGLE THROW (SPST)
40 AMP. RESISTIVE, INDUCTIVE, TUNGSTEN
OR 1000 VA PILOT DUTY 120/208/240 VOLT AC;
2 HP (24 FLA) - 120V AC; 5 HP (28 FLA) - 240V AC
OR 1000 VA PILOT DUTY 120/208/240 VOLT AC;
2 HP (24 FLA) - 120V AC; 5 HP (28 FLA) - 240V AC
WIRING INSTRUCTIONS: To wire switch follow diagram above.
Use solid or stranded COPPER only wire with insulation to suit
installation. See gauge selection table for normal service applica-
tions.To make power connections remove 1/2 inch of insulation
from wire ends. Insert bare ends of wire under the pressure plate
of terminals. Use 3/16 or larger screwdriver to tighten terminal
screws firmly. (25 lb-in minimum).
REPLACE INSULATOR BEFORE TURNING ON ELECTRICITY.
Use solid or stranded COPPER only wire with insulation to suit
installation. See gauge selection table for normal service applica-
tions.To make power connections remove 1/2 inch of insulation
from wire ends. Insert bare ends of wire under the pressure plate
of terminals. Use 3/16 or larger screwdriver to tighten terminal
screws firmly. (25 lb-in minimum).
REPLACE INSULATOR BEFORE TURNING ON ELECTRICITY.
PROGRAMMING INSTRUCTIONS
1. TO SET “ON” AND “OFF” TIMES: Hold trippers against edge
1. TO SET “ON” AND “OFF” TIMES: Hold trippers against edge
of CLOCK-DIAL, pointing to time (AM or PM) when ON and
OFF operations are desired, tighten tripper screws firmly. For
additional tripper pairs on CLOCK-DIAL order 156T1978A.
OFF operations are desired, tighten tripper screws firmly. For
additional tripper pairs on CLOCK-DIAL order 156T1978A.
2. TO SET TIME-OF-DAY: Pull CLOCK-DIAL outward. Turn in
either direction and align the exact time-of-day on the CLOCK-
DIAL (the time now, when switch is being put into operation) to
the pointer. DO NOT MOVE POINTER.
DIAL (the time now, when switch is being put into operation) to
the pointer. DO NOT MOVE POINTER.
OPERATING INSTRUCTIONS
• TO OPERATE SWITCH MANUALLY: Move MANUAL LEVER
• TO OPERATE SWITCH MANUALLY: Move MANUAL LEVER
below CLOCK-DIAL left or right as indicated by arrows. This
will not effect next operation.
will not effect next operation.
• IN CASE OF POWER FAILURE, reset CLOCK-DIAL to
proper time-of-day. See programming instructions.
INTERMATIC INCORPORATED
SPRING GROVE, ILLINOIS 60081-9698
158TS10941
TIME
POINTER
TIME
DIAL
DIAL
OFF
TRIPPER
TRIPPER
MANUAL
LEVER
LEVER
ON
TRIPPER
TRIPPER
CLOCK
MOTOR
GROUND
A
1
2
GRD.
120V
SUPPLY
TO
LOAD
LINE
NEUT.
WIRING
DIAGRAM
PRESSURE PLATE
TERMINAL SCREW
MAKE SURE WIRE
INSULATION CLEARS
PRESSURE PLATE
INSULATION CLEARS
PRESSURE PLATE
MINIMUM
COPPER
WIRE SIZE
(AWG)
MAX.
LOAD
(AMP)
MIN.
INSUL-
ATION
TEMP(°C)
75°C INSULATION MAX. MOTOR
LOAD (HP)
SINGLE PHASE
3 PHASE
120 V.
240 V.
208 V.
240 V.
14
12
10
12
10
8
15
20
30
40
20
30
40
60
60
60
75
60
60
75
1/2
1
2
2
-
2
2 1/2
3
5
5
N/A
N/A
CLOCK MOTOR: 110 -125 VOLTS - 60 HZ.
CLOCK MOTOR VOLTAGE AND CYCLE MUST BE AS SPECIFIED. TO
ORDER REPLACEMENT, INDICATE PART NO. (WG--) ON MOTOR COVER.
ORDER REPLACEMENT, INDICATE PART NO. (WG--) ON MOTOR COVER.
LR3730
Document1 10/30/03 1:30 PM Page 1