Carvin pm5 用户手册

Frequency Response: 75 Hz to 19.5 kHz ±3 dB

Useable Low Frequency: 67 Hz (-10 dB)

Power Handling: 100w Continuous Program Pw

Recommended Amp: 50 to 150 watts

Sensitivity: 93.5 dB SPL, 1 Watt @ 1 meter

Coverage Angles: 90° Horizontal, 90° Vertical

Nominal Impedance: 8

Ω

Inputs/Outputs: Spring Loaded Wire Terminals 

Enclosure Type: Vented Box

Enclosure Material: Injection Molded ABS Plastic

Dim/Wt: 6.75"W x 6.5"D x 10.25"H, 4.7lbs.

For your records, you may wish to record the following information.

Invoice Date_______________

CARVIN ENGINEERING DATA

INSTRUCTIONS

Congratulations on your selection of the PM5 speaker. The PM5 is a high-end water

resistant speaker that will give you reference monitor sound quality for use in
commercial and home stereo/home theater applications.  Removing the grill gives you
access to the OMNI™ tweeter that can be swiveled to focus the high frequencies to
your listening position.  As refelected in the LMS™ frequency curve, the response of
the PM5 is very accurate out to 19.5k.  The enclosure is a bass reflex design with a
tuned port giving you improved bass performance over conventional 5

1

/

4

” woofer

enclosures.  These powerful enclosures will easily handle 100 watts rms of continuous
program material, so don’t be afraid to turn them up.  However, as with any speaker,
observe the maximum rating.  The water resistant design includes specially treated
drivers for mounting outdoors.  The enclosure comes with built-in mounting slots
allowing the speaker to be hung on the wall without external brackets.  Carvin also
offers two additional mounting brackets for the PM5. See below

For optimal stereo performance place your speakers a minimum of 5 feet apart.  For

home theater surround sound installation, try to keep the speakers at ear level and equal
distances from your listening position.  If needed, pivot the OMNI™ tweeter for
precision adjustments.  You may prefer to leave the front grills off for indoor project
monitoring.  Please see Removing The Front Grills for instructions.

For outdoor or high ceiling installation, angle the speakers downward at the listening

position.  For longer life of your speakers, do not mount in an area where rain or
sprinklers will directly hit the enclosure.  Excess moisture will cause the hardware to rust.

To remove the grills and adjust the OMNI™ tweeter, use a small jewler’s screwdriver
or pick and insert along the edges and gently pry the front grill out.  Repeated
removal of the grill is not recomended as it may loosen the fit of the grill.

The PM5 enclosure has built-in screw mounting slots that allows the speakers to be
hung on a flat wall.   The optional PM5-UB “U bracket” allows you to angle the speaker
up, down, or side to side depending on how the speaker is mounted.  The PM5-CS
bracket is designed for multi-angle wall placement or for dropping through a ceiling.
When fastening the bracket to a wall or ceiling, make sure the mounting screws
penetrate a wooden stud or ceiling joist.  A saftey cable is included as a precaution.

Two standard spring loaded wire terminals are featured.

Be sure to use quality 16 gauge speaker wire for best
performance.  If you are installing your speakers
outdoors, make sure you are using speaker wire that is
rated to handle weather conditions.  Strip back 1/4” of the
insulation to expose the copper wires. Twist each end so
all wire strands enter the terminal easily.  Be sure to
connect the “striped” wire to the negative terminal and
the other to the positive terminal.  Match your polarity at your source (amp or
receiver).  Wiring your speakers out of phase will effect the quality of your sound
and reduce your bass response

Both the front grills and enclosure are paintable.  Protect your rear connection

plate by masking it off.  Leave the grills on while painting.  A small amount of
overspray through the grills will not hurt your speakers. Do not spray paint directly
into your speakers as it may damage them permanently.       

1)  DO NOT EXCEED THE POWER RATING as indicated.  Excessive power will

destroy drivers.  2)  DISTORTION from overdriven power amps will destroy drivers
much faster than clean power.

CARVIN speakers are covered by a ONE year limited warranty unless otherwise

stated.  Warranty coverage is limited to original manufactures defects only.
WARRANTY DOES NOT COVER: 1) Opened or burned voice coils.  2) Torn cones
or other damage caused by improper packing or abuse.  Return pre-paid by UPS.
Include your address and description of the problem.  Your speaker(s) will be
returned COD for the cost of shipping and repair if not covered under warranty.

INSPECT YOUR SPEAKERS FOR ANY DAMAGE which may have occurred during
shipping. If any damage is found, please notify the shipping company & CARVIN. 
SAVE THE CARTON & ALL PACKING MATERIALS.  In the event you have to re-ship
your unit.  CARVIN and the shipping company are not liable for any damage caused by
improper packing. SAVE YOUR INVOICE.  It will be required for warranty service if
needed in the future. SHIPMENT SHORTAGE.  If you find items missing, they may have
been shipped separately.  Please allow several days for the rest of your order to arrive
before inquiring.  Fill out and return the warranty card to Carvin.

76-00005  1098

12340 World Trade Drive, San Diego, CA  92128

(800) 854-2235  www.carvin.com

PM5-CS Wall & ceiling mounting
bracket with saftey cable.

PM5-UB U-bracket allows near 180º
pivot for direction adjustments.

Wall 
mountable

OR

Mount above

ceiling level and

drop through