Panasonic SC-PT850 操作指南
DISC OPERA
TIONS
ENGLISH
ENGLISH
41
RQT8043
RQTX0042
Changing the main unit and remote control
The remote control and main unit are factory-set to
“REMOTE 1” mode.
If your remote control affects other equipment during
operation, you can switch to operate in “REMOTE 2”
mode.
“REMOTE 1” mode.
If your remote control affects other equipment during
operation, you can switch to operate in “REMOTE 2”
mode.
To switch to “REMOTE 2” mode
1
While pressing and holding [
¡/ ¢] on the main
unit
“REMOTE 2” appears on the main unit display.
2
To operate in “REMOTE 2” mode
+
(Press and hold for 2 seconds)
To return to “REMOTE 1” mode
Perform steps 1 and 2 but use [1] instead of [2] for
both steps. (“REMOTE 1” appears on the main unit
during step 1.)
The remote control cannot work with the main
unit if their modes are different.
“REMOTE 1” or “REMOTE 2” appears on the main
unit display when you operate the remote control.
•
Perform steps 1 and 2 but use [1] instead of [2] for
both steps. (“REMOTE 1” appears on the main unit
during step 1.)
The remote control cannot work with the main
unit if their modes are different.
“REMOTE 1” or “REMOTE 2” appears on the main
unit display when you operate the remote control.
•
If “REMOTE 1” appears (The main unit is in
“REMOTE 1” mode.)
“REMOTE 1” mode.)
Press and hold [ENTER] and [1] on the remote
control for at least 2 seconds.
•
If “REMOTE 2” appears (The main unit is in
“REMOTE 2” mode.)
“REMOTE 2” mode.)
Press and hold [ENTER] and [2] on the remote
control for at least 2 seconds.
Note
You can still operate a television using the remote
control (
control (
\ page 40) even after switching the mode.
The speaker level settings can be optimized to
accommodate your room’s listening conditions
so that you can enjoy the ideal surround sound
experience. Using the supplied setup microphone,
the main unit adjusts the balance of the front
speakers, and the volume level of the center and
surround speakers automatically.
accommodate your room’s listening conditions
so that you can enjoy the ideal surround sound
experience. Using the supplied setup microphone,
the main unit adjusts the balance of the front
speakers, and the volume level of the center and
surround speakers automatically.
Keep as quiet as possible during the Auto
speaker setup. Loud voices, air-conditioning
noise, or excessive wind current may lead to
incorrect settings. The speakers output loud test
signals during the setup.
speaker setup. Loud voices, air-conditioning
noise, or excessive wind current may lead to
incorrect settings. The speakers output loud test
signals during the setup.
Preparation
• Turn off the television before starting the Auto
• Turn off the television before starting the Auto
speaker setup.
• Make sure that “DVD/CD” is selected as the source
and there are no discs in the tray.
• Ensure that headphones are disconnected.
1
While stopped
Connect the setup microphone.
2
Place the microphone at actual seating
position.
(At ear level when seated).
(At ear level when seated).
3
To start the setup.
(Press and hold)
AUTO SPEAKER SETUP
CENTER RIGHT
COMPLETE
LEFT SRD L SRD R
• The test signal is output from each speaker.
• “COMPLETE” is displayed when Auto speaker
• “COMPLETE” is displayed when Auto speaker
setup is completed.
To cancel the setup.
(Press and hold)
• “CANCEL” will be displayed if Auto speaker
setup is canceled.
Note
• Audio settings will be restored to default if the Auto
speaker setup is canceled.
• Please refer to the Troubleshooting guide if there is
any error message.
Adjusting the Speaker output level automatically: Auto speaker setup
RQTX0042-3B_new1.indd 41
RQTX0042-3B_new1.indd 41
4/2/07 1:48:24 PM
4/2/07 1:48:24 PM