Kicker Front Row™ 业主指南
3
Pro Tip: To get the best
performance from your new
KICKER gear, use genuine
KICKER accessories and
wiring.
performance from your new
KICKER gear, use genuine
KICKER accessories and
wiring.
Do not remove the diagnostics
and fi rmware port cover. Do not
connect any devices. KICKER is
not responsible for any damage
to the Front Row or devices that
have been connected to this
port.
and fi rmware port cover. Do not
connect any devices. KICKER is
not responsible for any damage
to the Front Row or devices that
have been connected to this
port.
source unit
high-level speaker
outputs
high-level speaker
outputs
to amplifi er
shield
+
–
core conductor
KICKER ZISL
source unit high-level
speaker outputs
speaker outputs
OR
to amplifi er
The Front Row has dual input sensitivity differential RCA inputs which will receive either high or low level signals
from your car stereo’s source unit. A high-level signal can be run from the source unit’s speaker outputs to
the stereo RCA inputs on the end panel of the Front Row using the KICKER ZISL as shown on the next page.
Alternatively, the signal can be delivered to the Front Row using the low-level RCA outputs on the source unit.
Keep the audio signal cable away from factory wiring harnesses and other power wiring. If you need to cross this
wiring, cross it at a 90 degree angle.
from your car stereo’s source unit. A high-level signal can be run from the source unit’s speaker outputs to
the stereo RCA inputs on the end panel of the Front Row using the KICKER ZISL as shown on the next page.
Alternatively, the signal can be delivered to the Front Row using the low-level RCA outputs on the source unit.
Keep the audio signal cable away from factory wiring harnesses and other power wiring. If you need to cross this
wiring, cross it at a 90 degree angle.
Install a 2A fuse within 18” (45cm) of the battery and in-line with the power cable connected to your Front Row.
If you ever need to remove the Front Row from the vehicle after it has been installed, the ground wire should be
the last wire disconnected from the Front Row--just the opposite as when you installed it.
If you ever need to remove the Front Row from the vehicle after it has been installed, the ground wire should be
the last wire disconnected from the Front Row--just the opposite as when you installed it.
INPUT
GAIN
MIN MAX
10 500Hz
50 500Hz
40 160Hz
0° 180°
10 500Hz
10 80Hz
MIN MAX
MIN MAX
MIN MAX
MIN MAX
MIN MAX
OUTPUT
LEVEL
OUTPUT
LEVEL
LO-P
ASS
X-OVER
HI-P
ASS
X-OVER
HI-P
ASS
X-OVER
SUBSONIC
PHASE
FREQUENCY
dB/OCT
LO-P
ASS
CLIP LIMITER
CLIP LIMITER
DC OFFSET/12V
CLIP LIMITER
OFF/ON
OFF/ON
OFF/LO
OFF/ON
TURN-ON
FREQUENCY
48/24/12
48/24/12
48/24/12
1X 10X
1X 10X
dB/OCT
dB/OCT
LO-P
ASS
X-OVER
OUTPUT
LEVEL
INPUT CLIP
POWER
FRONT
REAR/SURROUND
SUBWOOFER
INPUT
GAIN
INPUT
GAIN
INPUT CLIP
INPUT CLIP
REMOTE OUT
REMOTE IN
+12V
GND
remote turn-on
in and out
in and out
mount the Front Row to the
vehicle using the supplied screws
vehicle using the supplied screws
bare-metal
chassis ground
chassis ground
To vehicle
+12V constant
+12V constant
NOTE: Use 18 gauge
or larger wire for these
four connections.
or larger wire for these
four connections.
2012 FrontRow (ZXDSP) Rev G.indd 3
4/30/2012 1:55:46 PM