JBL Pro JBL VMA 260 业主指南

This device complies with part 15 of the FCC Rules and the Product speci-

fications noted on the Declaration of Conformity. Operation is subject to the 

following two conditions:

• 

 This device may not cause harmful 

interference, and 

• 

 This device must accept any interference received, including interfer-

ence that may cause undesired operation.  

Operation of this unit within significant 

electromagnetic fields should be avoided.

• 

Use only shielded interconnecting cables.

A molded mains plug that has been cut off from the cord is unsafe. 

Discard the mains plug at a suitable disposal facility. NEVER UNDER ANY 

CIRCUMSTANCES SHOULD YOU INSERT A DAMAGED OR CUT MAINS PLUG 

INTO A 13 AMP POWER SOCKET. Do not use the mains plug without the 

fuse cover in place.  Replacement fuse covers can be obtained from your 

local retailer.  Replacement fuses are 13 amps and MUST be ASTA approved 

to BS1362.

This equipment has been tested and found to comply with the limits for a Class B digital 
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide 
reasonable protection against harmful interference in a residential installation. This 
equipment generates, uses and can radiate radio frequency energy and, if not installed 
and used in accordance with the instructions, may cause harmful interference to radio 
communications. However, there is no guarantee that interference will not occur in a 
particular installation. If this equipment does cause harmful interference to radio or 
television reception, which can be determined by turning the equipment off and on, the 
user is encouraged to try to correct the interference by one of the following measures: 

• 

Reorient or relocate the receiving antenna.

• 

Increase the separation between the equipment and receiver.

• 

Connect the equipment into an outlet on a circuit different from that to which 
the receiver is connected.

• 

Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications not expressly approved by the party responsible for 
compliance could void the user’s authority to operate this equipment. 
 
This device complies with Part 15 of the FCC Rules. Operation is subject to the 
following two conditions:

1. 

This device may not cause harmful interference, and

2. 

This device must accept any interference received, including interference that 
may cause undesired operation.

This equipment complies with FCC radiation exposure limits set forth for an 
uncontrolled environment. This transmitter module must not be colocated or operated 
in conjunction with any other antenna or transmitter. This End equipment should be 
installed and operated with a minimum distance of 20 centimeters between the radiator 
and your body.

This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject 
to the following two conditions:

1. 

This device may not cause interference; and

2. 

This device must accept any interference, including interference that may cause 
undesired operation of the device.

This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject 
to the following two conditions:

1. 

l’appareil ne doit pas produire de brouillage;

2. 

l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,même 
si le brouillage est susceptible d’en compromettre le fonctionnement.

This device meets the exemption from the routine evaluation limits in section 2.5 of 
RSS102 and users can obtain Canadian information on RF exposure and compliance. 
 
Le dispositif répond à l’exemption des limites d’évaluation de routine dans la section 
2.5 de RSS102 et les utilisateurs peuvent obtenir des renseignements canadiens sur 
l’exposition aux RF et le respect.

The Industry Canada certification label of a module shall be clearly visible at all times 
when installed in the host device, otherwise the host device must be labelled to display 
the Industry Canada certification number of the module, preceded by the words 
“Contains transmitter module”, or the word “Contains”, or similar wording expressing 
the same meaning, as follows: “Contains transmitter module IC: 6132A-MB8811VMA” 

This End equipment should be installed and operated with a minimum distance of 20 
centimeters between the radiator and your body.

Cet équipement devrait être installé et actionné avec une distance minimum de 20 
centimètres entre le radiateur et votre corps. 

The end user manual shall include all required regulatory information/warning as shown 
in this manual.

If you want to dispose this product, do not mix it with 
general household waste. There is a separate collection 
system for used electronic products in accordance with 
legislation that requires proper treatment, recovery 
and recycling.

Private household in the 25 member states of the EU, in Switzerland 
and Norway may return their used electronic products free of charge 
to designated collection facilities or to a retailer (if you purchase a 
similar new one).

For Countries not mentioned above, please contact your local authori-
ties for a correct method of disposal.

By doing so you will ensure that your disposed product undergoes 
the necessary treatment, recovery and recycling and thus prevent 
potential negative effects on the environment and human health.

CAUTION!  Do not locate sensitive high-gain equipment such as 
preamplifiers or tape decks directly above or below the unit. Because this 
amplifier has a high power density, it has a strong magnetic field which 
can induce hum into unshielded devices that are located nearby. The field 
is strongest just above and below the unit.

If an equipment rack is used, we recommend locating the amplifier(s) 
in the bottom of the rack and the preamplifier or other sensitive equip-
ment at the top.

 
Apparatet må tilkoples jordet stikkontakt

Apparaten skall anslutas till jordat uttag

Laite on liitettävä suojakoskettimilla varustettuun pistorasiaan