K&M iPad® Mini Holder 业主指南

KÖNIG & MEYER GmbH & Co. KG 
Kiesweg 2, 97877 Wertheim, www.k-m.de
19713-300-55  Rev.6 / 19712-500-55  Rev.4  03-80-106-00  6/13

Material

Swivel Bearing: Polyamid PA-6
Holding Plate: PP 
Screws, nuts, washers, springs: steel galvanized

Max. load

iPad mini

Dimensions

208,7 x 89,6 x 143,7 mm
Box: 235 x 90 x 171 mm

Weight

net 0.49 kg, gross 0.67 kg

Thank you for choosing this product. The instructions provide directions
to all of the important set up and handling steps. We recommend you
keep these instructions for future reference.

FAULT FINDING (F) & REPAIR (R)
F: Holder is unstable

F: 

R: Check that it is properly screwed into the stand, if  

F: R:

needed tighten the screws 1-3

F: 

R: Tighten the wing nuts 4

F: iPad mini is not positioned in the holder properly   

F: 

R: Place the iPad mini into the holder correctly 6 and click 

F: R:

it into place 7

F: 

R: If needed, carefully bend the holding plate inwards 

The iPad mini holder can be adjusted according to the 
position and format. The iPad mini does not have to be
removed from the holding plate to make the adjustments.

POSITION
The iPad mini can be placed in any vertical / horizontal
position, the final position can be set. To do this:
10 Hold the iPad mini and loosen the wing nut somewhat
11 Pick the position (vertical / horizontal) and
12 Re-tighten the wing nut.

FORMAT
The holder is equipped with a 90°- rotating function. 
This allows the presentation of the iPad mini in the 
portrait and landscape positions.
13 Turn the holding plate either in the portrait or landscape  

position - or it can be tilted.     

- Hitches within the mount limit how far the holder can be 

-

turned.

- In addition, the holding plate clicks into place for both final 

-

positions, which means, that a the iPad mini will stay in the  

-

selected position.

ASSEMBLY
Assembly of the iPad mini holder is simple.
The prerequisite is a suitable stand
(see above SAFETY NOTES).
1 Turn the knurled washer (3/8") until it cannot go any 

further onto the thread of the stand.

2 This is followed by screwing on the mount
3 Tighten the mount and knurled washer
4 Tighten the wing nut
Placement of the IPAD MINI
5 Place the iPad mini according to the HOME-Button 

Symbol (is embossed on one side of the holder)

6 First PLACE the iPad mini into the bottom area and then...
7 ...and CLIP it into the top.
The disassembly is carried out in a reversed order.

- Only use suitable stands: Stability, 3/8"(5/8")-thread;

-

preferably K&M microphone stands or microphone holders

- Carefully clip the iPad mini onto the mounting plate and 

-

ensure that the iPad fit is secure

- Careful handling; especial when changing the 

-

position/format

- Specially adjusted to the iPad mini

ASSEMBLY

POSITION

FORMAT

PLACEMENT & REMOVAL of the IPAD MINI

Volume Control

Camera (Back)

Camera (Front)

Speaker

Lightning
connector

Microphone

On / Off
Switch

Microphone

3,5 mm
connector

bottom
PLACE

Final Position
- horizontal
- as far as it will go

Incline Position:
- tilted (0-90°)
- select any position (Secure position 

-

by tightening the wing nut)

Final Position
- vertical
- as far as it 

-

will go

Final Position
- landscape
- click into place

Incline Position:
- tilted
- does not click into place but it 

-

does stay in the selected position

Final Position
- portrait
- click into place

Lift up
the hook

Remove

top
CLIP ON

(the holder is embossed with information on where the iPad mini is to be placed)
(false placement results in the embossed user elements being covered up! Please note)