One World Technologies Inc. EL2200 用户手册
12 - English
MAINTENANCE
WARNING:
When servicing, use only identical
replacement parts. Use of any other parts could
create a hazard or cause product damage.
create a hazard or cause product damage.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, oil, grease, etc.
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, oil, grease, etc.
OPERATION
ATTACHING THE RADIO/CHARGER TO
A VERSATRACK TRACKWALL (NOT
INCLUDED)
See Figures 12 - 13, page iv.
The VersaTrack brackets included with your radio/charger
can be used to secure the product to the VersaTrack
trackwall.
NOTE: To purchase a VersaTrack trackwall, visit your
nearest Sears retail store or go to www.sears.com.
The VersaTrack brackets included with your radio/charger
can be used to secure the product to the VersaTrack
trackwall.
NOTE: To purchase a VersaTrack trackwall, visit your
nearest Sears retail store or go to www.sears.com.
Ensure that the trackwall is securely installed to the
mounting surface and the brackets are attached to the
radio correctly.
mounting surface and the brackets are attached to the
radio correctly.
Place the product on the trackwall by aligning the rib on
the brackets with the grooves in the trackwall as shown.
the brackets with the grooves in the trackwall as shown.
Slide the tool down until it is fully seated on the
trackwall.
trackwall.
All BLUETOOTH
®
enabled device controls can be used
normally while paired to the radio.
NOTE:
Volume for any device paired to the radio can
be adjusted using the volume control for that device or
by using the radio’s
by using the radio’s
VOL + or VOL - button.
To disconnect the BLUETOOTH
®
enabled device,
press and hold the
PRESET button. When the device
is disconnected, “bt” will begin flashing in the LCD
display and the radio/charger will begin searching for
another device.
display and the radio/charger will begin searching for
another device.
WARNING:
Do not at any time let brake fluids,
gasoline, petroleum-based products, penetrating
oils, etc., come in contact with plastic parts.
Chemicals can damage, weaken or destroy plastic
which could result in serious personal injury.
oils, etc., come in contact with plastic parts.
Chemicals can damage, weaken or destroy plastic
which could result in serious personal injury.
Only the parts shown on the parts list are intended to
be repaired or replaced by the customer. All other parts
should be replaced by a qualified service dealer.
be repaired or replaced by the customer. All other parts
should be replaced by a qualified service dealer.
FCC COMPLIANCE
WARNING:
Changes or modifications to this unit not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. This Class B digital apparatus complies with Canadian ICES-003. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. Operation is subject to the following two conditions:
1. This device may
15 of the FCC Rules. This Class B digital apparatus complies with Canadian ICES-003. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. Operation is subject to the following two conditions:
1. This device may
not
cause harmful interference and,
2. This device must accept any interference received, including interference that may cause undesired operation.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment on and off, the
user is encouraged to try to correct the interference by one or more of the following measures:
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment on and off, the
user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.