Elec-Tech International Co. Ltd. 90600120 用户手册

THANK YOU

We appreciate the trust and confidence you have placed in Commercial Electric through the purchase of this motion

sensor module. We strive to continually create quality products designed to enhance your home. Visit us online to see

our full line of products available for your home improvement needs. Thank you for choosing Commercial Electric!

Warranty

WHAT IS COVERED

The manufacturer warrants this product to be free from defects in materials and workmanship for

a period of five (5) years from date of purchase. This warranty applies only to the original consumer

purchaser and only to products used in normal use and service. If this product is found to be defective,

the manufacturer’s only obligation, and your exclusive remedy, is the repair or replacement of the

product at the manufacturer’s discretion, provided that the product has not been damaged through

misuse, abuse, accident, modifications, alterations, neglect, or mishandling.

WHAT IS NOT COVERED

This warranty shall not apply to any product that is found to have been improperly installed, set-up, or

used in any way not in accordance with the instructions supplied with the product. This warranty shall

not apply to a failure of the product as a result of an accident, misuse, abuse, negligence, alteration,

faulty installation, or any other failure not relating to faulty material or workmanship. This warranty

shall not apply to the finish on any portion of the product, such as surface and/or weathering, as this is

considered normal wear and tear.
The manufacturer does not warrant and specifically disclaims any warranty, whether express or

implied, of fitness for a particular purpose, other than the warranty contained herein. The manufacturer

specifically disclaims any liability and shall not be liable for any consequential or incidental loss or

damage, including but not limited to any labor / expense costs involved in the replacement or repair of

said product.
Contact the Customer Service Team at 1-877-527-0313 or visit www.HomeDepot.com.

Questions, problems, missing parts? Before returning to the store,

call Commercial Electric Customer Service

8 a.m. - 7 p.m., EST, Monday - Friday, 9 a.m. - 6 p.m., EST, Saturday

1-877-527-0313

HOmEDEpOT.COm

Use and Care GUide

MOTiOn sensOr MOdULe

item #1000000000

Model #

90600120

Care and Cleaning

CaUTiOn: Before attempting to clean the sensor, disconnect the power to the fixture by turning the breaker

off or removing the fuse from the fuse box.

Clean the sensor with a soft, dry cloth.

Do not use cleaners with chemicals, solvents, or harsh abrasives.

Do not use liquid cleaner on the sensor.

Pre-installation

Before beginning assembly, installation or operation of the product, make sure all parts are present.

Compare parts with the package contents list. If any part is missing or damaged, do not attempt to

assemble, install or operate the product. Contact customer service for replacement parts.

nOTe: Keep your receipt and these instructions for proof of purchase.

If you are unfamiliar with electrical installations, we recommend you contact a qualified electrician to do

the installation.

TOOlS REqUIRED

pACKAgE CONTENTS

part

Description

quantity

Motion Sensor Module

HARDWARE INClUDED

part

Description

quantity

Locknut (3/4 in.)

Lock Washer (3/4 in.)

Locknut (1/2 in.)

Lock Washer (1/2 in.)

Wire Connectors

Male to Male Connector

installation

WarninG: RISK OF ELECTRIC SHOCK. Ensure the electricity to the wires you are working on is shut off.

Either remove the fuse or turn off the circuit breaker before beginning assembly or installation.

nOTiCe: This motion sensor module works with direct hard wired LED and fluorescent light fixtures as well as

with selected Commercial Electric linkable plug-in LED light fixtures. Visit HomeDepot.com for a list of compatible

Commercial Electric linkable plug-in fixtures.

nOTiCe: The motion sensor can be used for fixtures installed up to 18 feet high.

preparing the fixture

Remove the diffuser/lens to allow access to the

fixture wiring.

Remove the knockout

where you wish to mount

the sensor module.

installing for Use with direct Wired Fixtures

Determining the knockout size

Choose the appropriate knockout size for

your fixture, either 3/4” or 1/2”, and use only

the locknut and lock washer for that size.

Connecting the sensor module to the fixture

Insert the threaded end of the sensor module (A) completely

into the selected knockout hole and through the lock washer

(BB/DD). Then tighten the locknut (AA/CC) securely onto the

threaded end of the sensor module (A).

nOTe: For a firm fit, gently use pliers to tighten the locknut (AA/CC).

Feeding the wires

Feed the electrical connection wires from

the sensor module (A) through the selected

knockout hole and then through the lock

washer (BB/DD) followed by the locknut

(AA/CC).

nOTe: The lock washer (BB or DD) and

locknut (AA or CC) should be on the inside of

the fixture wall with the wires coming through

the center of each.

making the electrical connections

Connect the hot (black) wire from the sensor (A) to the black

wire from the electrical box.

Connect the neutral (white) wire from the sensor (A) to the

white wire from the fixture and the white wire from the

electrical box.

Connect the secondary live wire

(red) from the sensor (A) to the live

wire (black) from the fixture.

Cover the three wire connections

using the wire connectors (EE).

nOTiCe: The green wire from the fixture

should continue to be connected to the

grounding wire from the electrical box.

Attaching the diffuser to the housing

Replace the diffuser/lens on the light fixture.

Restore power to the electrical box.

Turn on the light switch to activate the

fixture.

installing for use with selected Commercial electric linkable

plug-in Led light fixtures

preparing the fixture

Unplug the power cord from the

electrical outlet and from the light

fixture.

Connecting the sensor module to the

fixture

Insert the small male-to-male connector (FF) to

the Power Out side of the sensor module (A).

Push the other end of the male-to-male

connector (FF) into the Power end of the fixture.

Make sure both connections fit securely.

nOTe: The sensor module (A) notes which end is

Power In and which is Power Out.

Turning on the power

Insert the power cord firmly into the Power In end of

the sensor module (A).

Plug the power cord into the electrical outlet.

Turn on the light fixture.

adjusting the Motion sensor

safety information

WarninG: Carefully read and understand the

information given in this manual before beginning the

assembly and installation. Failure to do so could lead

to electric shock, fire, or other injuries which could be

hazardous or even fatal.

WarninG: Ensure the electricity to the wires you

are working on is shut off. Either remove the fuse or

turn off the circuit breaker.

FCC ID:XZH-90600120
nOTiCe: This device complies with Part 15 of the FCC

Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2)

this device must accept any interference received, including

interference that may cause undesired operation.
CaUTiOn: Changes / modifications not approved by the

responsible party could void the user’s authority to operate

the equipment.

Wire Strippers

Safety Goggles

Ladder

Gloves

Pliers

installing for Use with direct Wired Fixtures (continued)

Troubleshooting

WarninG: Before doing any work on the motion sensor module, disconnect power to the light fixture.

Minor problems often can be fixed without the help of an electrician.

installing for use with selected Commercial electric linkable

plug-in Led light fixtures (continued)

Detection area

The motion detection

area can be adjusted

by selecting the

combination of settings

on the DIP switches

for the desired motion

detection area.

detection area

Coverage By install Height

DIP 1 DIP 2

10 ft. Ceiling

9 ft. Ceiling

8 ft. Ceiling

100%

43 ft. x 10 ft.

40 ft. x 9 ft.

39 ft. x 8 ft.

75%

36 ft. x 10 ft.

34 ft. x 9 ft.

33 ft. x 8 ft.

III

50%

26 ft. x 10 ft.

23 ft. x 9 ft.

23 ft. x 8 ft.

10%

7 ft. x 10 ft.

7 ft. x 9 ft.

7 ft. x 8 ft.

DIP 3

DIP 4

5 sec.

90 sec.

III

5 min.

15 min.

DIP 5

DIP 6

Disable

50 lux.

III

10 lux.

2 lux.

I - 100%

II - 75%

III - 50%

IV - 10%

I - 5 sec.

II - 90 sec.

III - 5 min.

IV - 15 min.

I - Disable

II - 50 lux.

III - 10 lux.

IV - 2 lux.

Motion Sensor

Detection Area

Hold-time

Daylight Sensor

Light Level

DIP 1

DIP 2

DIP 3

DIP 4

DIP 5

DIP 6

75%

5 minutes

Disabled

The sensor comes from the factory with the following settings:

Detection Area: 75%

Hold Time: 5 Minutes

Daylight Sensor: Photocell Disabled

To adjust the settings, simply move the DIp switches to the settings you prefer.

Hold-time

Hold-time is the time period the light will remain

on after the person has left the detected area.

The amount of time the light remains on can be

adjusted by selecting the combination of settings

on the DIP switches for the desired hold-time.

Daylight sensor

The daylight threshold can be adjusted by

selecting the combination of settings on the DIP

switches to determine the level of darkness when

the light will turn on automatically.

Problem

Possible Cause

solution

The fixture will not light.

The power is off.

Ensure the power supply and circuit breaker are both in the on position.

There is a bad connection. Check to ensure proper wire connections are made. Contact a qualified electrician.
The motion sensor module

is mounted higher than

18 ft.

Mount the fixture with the motion sensor module at 18 ft. or lower.

The fuse blows or the

circuit breaker trips when

the light is turned on.

The wires are crossed

or the power wire is

grounding out.

Check the wire connections.

Contact a qualified electrician or call Commercial Electric customer service

1-877-527-0313.

The light is not staying on

long enough after the last

motion is detected.

The hold-time setting

needs to be adjusted.

Factory setting is a 5 minute hold time. To increase the time

period the light remains on, please refer to the Adjusting the

Motion Sensor section of the instruction manual to adjust the

4th dip switch to the preferred setting.

The light is staying on too

long after the last motion is

detected.

The hold-time setting

needs to be adjusted.

Factory setting is a 5 minute hold time. To decrease the time

period the light remains on, please refer to the Adjusting the

Motion Sensor section of the instruction manual to adjust the

3rd and 4th dip switches to the preferred setting.

The motion sensor is not

detecting motion in a large

enough area.

The motion sensor needs

to be adjusted.

To increase the motion detection area, please refer to the

Adjusting the Motion Sensor section of the instruction manual

to adjust the 1st and 2nd dip switches to the preferred setting.

The motion sensor is

detecting motion in too

large an area.

The motion sensor needs

to be adjusted.

To decrease the motion detection area, please refer to the

Adjusting the Motion Sensor section of the instruction manual

to adjust the 1st and 2nd dip switches to the preferred setting.

The motion sensor is

detecting motion during

daylight hours and turning

the light on when I do not

need it on.

The daylight sensor needs

to be adjusted.

Ensure the 5th and 6th dip switches are set to detect light at

the 50 lux, 10 lux or 2 lux settings. Please refer to the Adjusting

the Motion Sensor section of the instruction manual to adjust

the 5th and 6th dip switches to the preferred setting.

The motion sensor is not

detecting motion and

turning the light on during

daylight hours when I

need it to.

The daylight sensor needs

to be adjusted.

Ensure the 5th and 6th dip switches are set at “disable”. This

will allow the light to turn on when motion is detected at any

light level. Please refer to the Adjusting the Motion Sensor

section of the instruction manual to adjust the 5th and 6th dip

switches to the preferred setting.

Knockout holes

AA/CC

15 min.

5 sec.

90 sec.

100%

Disable

50 lux.

III

10 lux.

2 lux.

III

50%

10%

FCC ID: XZH-9050102016

BB/DD

DIP Switches

BB/DD

Black

BB/DD

AA/CC

Red

White

Black