Graupner GmbH & Co. KG MC-20 用户手册
214 Detail program description - Teacher/pupil
Wireless HoTT system
Wireless operation of the
mc-20
HoTT trainer
mode system is also possible. To do so, the teacher
transmitter must be "connected" to a pupil transmitter
as described below. Prior to this, however, the
training model's receiver must be bound to the PUPIL
transmitter. This confi guration is possible between
transmitters which have the "BIND:" option in the
»Teacher/pupil« menu.
transmitter must be "connected" to a pupil transmitter
as described below. Prior to this, however, the
training model's receiver must be bound to the PUPIL
transmitter. This confi guration is possible between
transmitters which have the "BIND:" option in the
»Teacher/pupil« menu.
Preparing for training mode
Teacher transmitter
The training model must be programmed completely,
i.e. with all of its functions including trims and any
mixer functions, in one model memory of the HoTT
teacher transmitter. The model to be used for
training must therefore be under the complete
control of the teacher transmitter. The fi nal step
in preparation, however, is to bind the training
model to the pupil transmitter. For a detailed
description of the binding process, please
consult pages 77 and 85.
The training model must be programmed completely,
i.e. with all of its functions including trims and any
mixer functions, in one model memory of the HoTT
teacher transmitter. The model to be used for
training must therefore be under the complete
control of the teacher transmitter. The fi nal step
in preparation, however, is to bind the training
model to the pupil transmitter. For a detailed
description of the binding process, please
consult pages 77 and 85.
Pupil transmitter
If you are using an "
If you are using an "
mc" or "mx" series transmitter,
it is best to activate a free model memory with the
required model type ("Fixed-wing" or "Heli"). Assign
the model name "Pupil" and set up the stick mode
(mode 1 … 4) and "Throttle (or collective pitch) min.
forward/back" to suit the pupil's preferences. All
other options are left at their default values. All other
settings, including all mixer and coupling functions,
are confi gured exclusively on the teacher transmitter,
which in turn transmits them to the model.
When assigning control functions, the usual
conventions must be observed:
required model type ("Fixed-wing" or "Heli"). Assign
the model name "Pupil" and set up the stick mode
(mode 1 … 4) and "Throttle (or collective pitch) min.
forward/back" to suit the pupil's preferences. All
other options are left at their default values. All other
settings, including all mixer and coupling functions,
are confi gured exclusively on the teacher transmitter,
which in turn transmits them to the model.
When assigning control functions, the usual
conventions must be observed:
Channel
Function
1
Motor throttle/collective pitch
2
Aileron/roll
3
Elevator/pitch-axis
4
Rudder/tail rotor
If other control functions are to be transferred to the
pupil transmitter in addition to the functions of the two
dual axis sticks (1 … 4), access the »Control adjust«
menu in the pupil transmitter and assign those inputs
which correspond to enabled function or transmitter
control inputs 5 … 12 as shown in the »Teacher/
pupil« menu of the teacher transmitter. Afterwards,
assign the operating elements appropriately.
pupil transmitter in addition to the functions of the two
dual axis sticks (1 … 4), access the »Control adjust«
menu in the pupil transmitter and assign those inputs
which correspond to enabled function or transmitter
control inputs 5 … 12 as shown in the »Teacher/
pupil« menu of the teacher transmitter. Afterwards,
assign the operating elements appropriately.
Important:
If you should forget to assign a transmitter
control on the pupil side, then the affected servo
or servos will remain in the center position when
the transfer is made to the pupil transmitter.
If you should forget to assign a transmitter
control on the pupil side, then the affected servo
or servos will remain in the center position when
the transfer is made to the pupil transmitter.
Preparing the teacher and pupil transmitters
Once you have bound the training model to the pupil
transmitter, now switch on the teacher transmitter. On
both transmitters, use the selection keys on the left or
right touch pad, page to the »Teacher/pupil« menu
option on the multi-function menu:
transmitter, now switch on the teacher transmitter. On
both transmitters, use the selection keys on the left or
right touch pad, page to the »Teacher/pupil« menu
option on the multi-function menu:
Phase trim
Non-delayed chan
Timers (general)
Fl. phase timers
Wing mixers
Free mixers
MIX active/phase
MIX-only channel
Dual mixer
Fail-safe adjust
Teacher / pupil
Tx. output swap
Non-delayed chan
Timers (general)
Fl. phase timers
Helicopter mixer
Free mixers
MIX active/phase
MIX-only channel
Dual mixer
Swashplate mixer
Fail-safe adjust
Teacher / pupil
Tx. output swap
Briefl y tap the center
SET
key of the right touch pad
to open this menu option:
T R A I N E R / s t u d e n t
P
T
T
2
3
4
5
BIND:
SW: –––
1
n/a
6
7
8
9 10 11 12
Note:
The screen image shown above shows the menu
in its initial state: No transmitter controls have been
released to the pupil ( ) and no switch has been
assigned
("SW: ---" bottom left in the screen image).
The screen image shown above shows the menu
in its initial state: No transmitter controls have been
released to the pupil ( ) and no switch has been
assigned
("SW: ---" bottom left in the screen image).
Pupil transmitter
Use the selection keys on the left or right touch pad
to move the marker frame to the "BIND" input fi eld. If
there is a switch shown at the right of "S:" then this
must fi rst be erased, see screen image:
Use the selection keys on the left or right touch pad
to move the marker frame to the "BIND" input fi eld. If
there is a switch shown at the right of "S:" then this
must fi rst be erased, see screen image:
T R A I N E R / s t u d e n t
P
T
T
2
3
4
5
BIND:
SW:
1
n/a
6
7
8
9 10 11 12
Ä
–––