Graupner GmbH & Co. KG MC-20 用户手册
69
Detail program description - Model select
Model select
Call up model 1 … 80
The basic operation of the transmitters keys was
explained on pages 28 and 29 and, on the previous
double-page, explanations were provided for
navigating to the multifunction list and about how
to make allocations for a new model memory. At
this point we now wish to begin with the "normal"
description of individual menu items in the sequence
they are arranged in the transmitter. Therefore we will
begin with the menu …
explained on pages 28 and 29 and, on the previous
double-page, explanations were provided for
navigating to the multifunction list and about how
to make allocations for a new model memory. At
this point we now wish to begin with the "normal"
description of individual menu items in the sequence
they are arranged in the transmitter. Therefore we will
begin with the menu …
Model select
Ser vo adjustment
Stick mode
Control adjust
Dual Rate / Expo
Channel 1 cur ve
Switch display
Model select
Copy / Erase
Suppress codes
Suppress models
Base setup model
Model type
Model select
Ser vo adjustment
Stick mode
Control adjust
Dual Rate / Expo
Channel 1 cur ve
Switch display
Copy / Erase
Suppress codes
Suppress models
Base setup model
Model type
As many as 80 complete model settings, including
digital trim values for the trim wheel, can be stored.
Trimming is stored automatically such that a
switchover from one model to another does not cause
a loss of current trim settings. To the right of the
model number, each occupied model memory line in
this display shows a pictograph of the model type as
well as the model's name entered for the model in its
»Basic settings, model« menu, page 76 or 84. The
code, if present, for the receiver "bound" to the model
memory location will appear after the model number.
Select the »Model select« menu with the selection
digital trim values for the trim wheel, can be stored.
Trimming is stored automatically such that a
switchover from one model to another does not cause
a loss of current trim settings. To the right of the
model number, each occupied model memory line in
this display shows a pictograph of the model type as
well as the model's name entered for the model in its
»Basic settings, model« menu, page 76 or 84. The
code, if present, for the receiver "bound" to the model
memory location will appear after the model number.
Select the »Model select« menu with the selection
keys of the left or right touch pad then briefl y tap on
the
the
SET
key of the right touch pad.
Attention!
Switch-OFF
the Receiver first!
If this message appears, there is a telemetry connection
to an operationally ready receiver system. Switch that
receiver system off.
to an operationally ready receiver system. Switch that
receiver system off.
03
04
Ultimate
02
00:44hR12
Starlet
BELL47G
00:33hR08
00:22hR08
Test
trim needed
¿¿¿
free
¿¿¿
¿¿¿
free
¿¿¿
05
06
01
01:23hR16
Graubele
1234g/080811
Now, with the
cd selection keys of the left or right
touch pad, select the desired model memory from the
list and activate it with a tap on the
list and activate it with a tap on the
SET
key. A tap on
the
ESC
key will cause a return to the previous menu
page without activating a model change.
Notes:
If, after a model change, the "Throttle too high"
•
warning appears, the throttle/pitch joystick (C1)
or the throttle limiter – by default, the right-side
proportional rotary slider – is too far in the full
throttle direction.
If a model change causes the message …
or the throttle limiter – by default, the right-side
proportional rotary slider – is too far in the full
throttle direction.
If a model change causes the message …
•
BIND. N/A
OK
… to appear then binding settings should be
checked.
If a model change causes the message …
checked.
If a model change causes the message …
•
Fail Safe
setup
t.b.d.
… to appear then respective failsafe settings
should be checked.
If battery voltage is too low, the model switchover
should be checked.
If battery voltage is too low, the model switchover
•
cannot be made due to reasons of safety. An
appropriate message will appear in the screen:
appropriate message will appear in the screen:
not possible now
voltage too low
voltage too low