Meru Networks Inc. OAP433E 用户手册
Note
When not using antenna connectors on the OAP433e, keep the covers securely
attached for weather protection. Once the AP is deployed, these unused
connectors must be properly terminated.
attached for weather protection. Once the AP is deployed, these unused
connectors must be properly terminated.
Caution!
Caution! Equipment shall be installed in accordance with the National Electrical
Code ANSI/NFPA 70 and the Canadian Electrical Code, Part 1, and when
applicable, the National Electrical Safety Code, IEEE C2.
Code ANSI/NFPA 70 and the Canadian Electrical Code, Part 1, and when
applicable, the National Electrical Safety Code, IEEE C2.
Equipment shall be properly grounded according to Chapter 8 of ANSI/NFPA 70,
the National Electrical Code (NEC) and the Cable distribution system should be
grounded (earthed) in accordance with ANSI/NFPA 70, the National Electrical
Code (NEC), in particular Section 820.93, Grounding of the Outer Conductive
Shield of a Coaxial Cable.
the National Electrical Code (NEC) and the Cable distribution system should be
grounded (earthed) in accordance with ANSI/NFPA 70, the National Electrical
Code (NEC), in particular Section 820.93, Grounding of the Outer Conductive
Shield of a Coaxial Cable.
The separate protective earthing terminal provided on this product shall be
permanently connected to earth.
permanently connected to earth.
6.13
Approved Antennas for OAP433e
Only approved antennas may be used in conjunction with OAP433e access points.
Access Points have been designed to operate with the antennas listed below.
Antennas not included in this list are strictly prohibited for use with these devices.
The required antenna impedance is 50 ohms.
Access Points have been designed to operate with the antennas listed below.
Antennas not included in this list are strictly prohibited for use with these devices.
The required antenna impedance is 50 ohms.
Meru Part Number
Gain @ 2.4 GHz
Gain @ 5.x GHz
Description
ANT-A08O-NM-1
NA
8.0 (5150~5350
MHz)
MHz)
Omnidirectional
antenna, 5150 - 5350
MHz (US, Non-DFS
band UNII-1), N-type
connector
antenna, 5150 - 5350
MHz (US, Non-DFS
band UNII-1), N-type
connector
ANT-A08O-NM-2
NA
8.0 (5470 ~5875
MHz)
MHz)
Omnidirectional
antenna, 5470 - 5875
MHz (US, EMEA,
Others, DFS band UNII-
2 & UNII-2e), N-type
connector
antenna, 5470 - 5875
MHz (US, EMEA,
Others, DFS band UNII-
2 & UNII-2e), N-type
connector
ANT-BG08O-NM
8.0
NA
Omnidirectional
antenna, 2400 - 2500
MHz Worldwide, N-type
connector
antenna, 2400 - 2500
MHz Worldwide, N-type
connector
ANT-O4ABGN-0606-O-N
6.0
6.0
Dual band wall-mask
mount omnidirectional
outdoor, N-type
connector with 4 RG58
coaxial cable leads
mount omnidirectional
outdoor, N-type
connector with 4 RG58
coaxial cable leads
ANT-O4ABGN-0607-PT-N
6.0
7.0
Dual band wall-mask
mount directional patch
outdoor, N-type
connector with 4 RG58
coaxial cable leads
mount directional patch
outdoor, N-type
connector with 4 RG58
coaxial cable leads
6.14
Installation with ANT-O4ABGN-0606-O-N
The following diagram show the installation with Installation with ANT-O4ABGN-
0606-O-N antenna. See Figure 37, OAP433e deployment with ANT-O4ABGN-
0606-O-N antenna in ETSI
0606-O-N antenna. See Figure 37, OAP433e deployment with ANT-O4ABGN-
0606-O-N antenna in ETSI
Figure 38, OAP433e deployment with ANT-O4ABGN-
0606-O-N antennas
&
Figure 38, OAP433e deployment with ANT-O4ABGN-0606-
O-N antennas
Figure 37, OAP433e deployment with ANT-O4ABGN-0606-O-N antenna in ETSI