Zucchetti Axess S.p.A. 90401-14 用户手册
904 RFID2 1356 Shortform-ENG-16.doc
p.n. 19040220
Output Assignment
for TMC MAX
1
Blue
GND
2
Red
Power 5 Vdc
3
Pink
Clock Output
4
5 White
Data Output
6
7 Yellow GREEN LED
8
8
Grey
RED LED
This device only conforms to all
the standards of the CE mark if
the installation and user
instructions contained in this
document are followed correctly.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
INSTRUCTIONS FOR FCC ID LABELING
Module type: transmitter 90401-14
FCC-ID: SYL90401-14
This intends to inform you how to specify the FCC ID of our transmitter module 90401-14 on your final product. Based on the Public Notice from FCC, the product into which our
transmitter module is installed must display a label referring to the enclosed module. The label should use wording such as “Contains transmitter module FCC ID: SYL90401-14” or
“Contains FCC ID: SYL90401-14”, any similar wording with the same meaning may be used.
Module type: transmitter 90401-14
FCC-ID: SYL90401-14
This intends to inform you how to specify the FCC ID of our transmitter module 90401-14 on your final product. Based on the Public Notice from FCC, the product into which our
transmitter module is installed must display a label referring to the enclosed module. The label should use wording such as “Contains transmitter module FCC ID: SYL90401-14” or
“Contains FCC ID: SYL90401-14”, any similar wording with the same meaning may be used.
904.201.14 RFID/2 13.56MHz TTL module
904.202.14 RFID/2 13.56MHz Buffered module
904.202.14 RFID/2 13.56MHz Buffered module
Proximity R/W modules
for passive ISO14443A/B, and ISO15693 inductive tags.
for passive ISO14443A/B, and ISO15693 inductive tags.
Transponder type
ISO14443A – ISO15693 standard – SR176 – SRIX4K
Interface
Electrical: According to model p/n and configuration wires.
Data Format: According to configuration wires.
Data Format: According to configuration wires.
Reading range
About 3 cm, with ISO card, in good conditions.
Don’t mount the reader directly on metal surface.
Don’t mount the reader directly on metal surface.
Audio-visual
indication
indication
Two LEDs (Red and Green) driven by connecting the Grey and Yellow wires to GND, respectively. If these wires
are not connected, the Red LED is still on as the module is powered, turns off in case of good decode, then turns
back on only when the tag exits the reading range, while the Green LED blinks for a while in case of good decode.
are not connected, the Red LED is still on as the module is powered, turns off in case of good decode, then turns
back on only when the tag exits the reading range, while the Green LED blinks for a while in case of good decode.
Power supply
904.201.14 --- 5 Vdc. (+/-10%), 65mA typical, 100mA max.
904.202.14 --- 12 Vdc. (9..18V) , 65mA typical, 100mA max.
904.202.14 --- 12 Vdc. (9..18V) , 65mA typical, 100mA max.
Dimensions
101 x 44 x 23 mm (outline)
Temperature range
-20° to +60°C.
Interface cable
300cm
AXESS TMC srl
Via della Filanda, 22 - 40133 Bologna - Italy
Tel:+39 051 3519311 - Fax: +39 051 3519399
www.axesstmc.com
Output Assignment
for TMC PROX & TRAX
5 Red
Power 5Vdc
4 Blue
GND
3 White
Data Output
2 Pink
Clock Output
1
(n.c. battery aside)
Connector
The 904.201.14 is supplied with a 8-
pin MOLEX connector. It is factory
configured for using (as a magnetic
emulation
pin MOLEX connector. It is factory
configured for using (as a magnetic
emulation
reader)
with
TMC
914.003.20
HotMAX
boards.
Connection to PROX (and
TRAX
)
terminals is also possible changing
the pins order and reducing the
connector as shown in the rightmost
table.
the pins order and reducing the
connector as shown in the rightmost
table.
Note: to modify the pin connections or
change the connector size, just press
a little with a screwdriver into the
corresponding rectangular hole and
pull the wire at the same time.
Then re-insert it in the required
position.
change the connector size, just press
a little with a screwdriver into the
corresponding rectangular hole and
pull the wire at the same time.
Then re-insert it in the required
position.
1 2 3 4 5 6 7 8
Data transmission
Data are transmitted in magstripe reader emulation (Clk&Data), or serial interface at 57600,n,8,1 with ASCII protocol, or Wiegand* 26bit.
Commands to the R/W module can be issued only using the serial interface, with any TTY terminal emulator or serial communication program (a
TTL/USB conversion cable, p/n 908.000.20, is available for 904.201.14). For further details and a list of the available commands/answers and their
format please refer to the “RFID 13.56MHz Manual”, that can be downloaded from AxessTMC web site
Commands to the R/W module can be issued only using the serial interface, with any TTY terminal emulator or serial communication program (a
TTL/USB conversion cable, p/n 908.000.20, is available for 904.201.14). For further details and a list of the available commands/answers and their
format please refer to the “RFID 13.56MHz Manual”, that can be downloaded from AxessTMC web site
http://www.axesstmc.com/
, in the Manuals
section of the Partners Area.
Autoread configuration
The modules are preprogrammed for automatic retrieving and transmission of the UID code always present in all tags, when a card enters in the field
range. The modules can also be programmed for reading and transmission of some other content of the card: please refer to the above mentioned
“RFID 13.56MHz Manual” for the possible options.
range. The modules can also be programmed for reading and transmission of some other content of the card: please refer to the above mentioned
“RFID 13.56MHz Manual” for the possible options.
Default UID Output Format
(* Wiegand output: when available)
C
LK
D
ATA
S
ERIAL
57600,
N
,8,1
W
IEGAND
*
ISO14443A (mifare
®
)
4 bytes to 10 digit
;2796021616?>
;2796021616?>
4 bytes to 10 digit
2796021616<CR>
2796021616<CR>
LSB 26 bit
16759248
16759248
ISO15693
ISO14443B (SR176, SRIX4K)
ISO14443B (SR176, SRIX4K)
8 bytes to 20 digit
(2+2+4) (5+5+10)
;53250021984003940284?>
8 bytes to 20 digit
(2+2+4) (5+5+10)
53250021984003940284<CR>
LSB 26 bit
16718364
16718364
904.201.14 Colors Output Assignments
C
LK
D
ATA
S
ERIAL
TTL
W
IEGAND
*
Red
Power 5 Vdc
Blue
GND
Yellow
GREEN LED command (to Gnd)
Grey
RED LED command (to Gnd)
Pink
Clock
wired with Brown
Data1
White
Data
TXD
Data0
Green
open
RXD
GND
Brown
Reserved for configuration and firmware update
904.202.14 Colors Output Assignments
S
ERIAL
RS232
W
IEGAND
*
Red
Power 12V dc
Blue
GND
Yellow
GREEN LED command (to Gnd)
Grey
RED LED command (to Gnd)
Pink
open
Data1
White
TXD
open
Green
RXD
wired with Brown
Brown
Data0