The Bodine Company FEBNET02 用户手册
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
bodine
®
WHEN USING ELECTRICAL EQUIPMENT, BASIC
SAFETY PRECAUTIONS SHOULD ALWAYS BE
FOLLOWED, INCLUDING THE FOLLOWING:
SAVE THESE INSTRUCTIONS
THIS PRODUCT CONTAINS A RECHARGEABLE NICKEL-CADMIUM BATTERY.
THE BATTERY MUST BE RECYCLED OR DISPOSED OF PROPERLY.
©The Bodine Company, Inc.
236 Mt. Pleasant Rd. • Collierville, TN USA 38017-2752 • Tech Support 888-263-4638 • Fax 901-854-1630 • www.bodine.com
75000022
NETWORKED EMERGENCY BALLAST
Installation Instructions
1. To prevent high voltage from being present on red & yellow output leads prior to installation, inverter connector must be
open. Do not join inverter connector until installation is complete and AC power is supplied to the emergency ballast.
2. This product is for use with most 17 W through 215 W single pin or bipin fluorescent lamps, including standard, energy saving, HO,
VHO, circline, U-shaped, rapid-start long compact and 18 W through 42 W (4-pin) compact lamps without integral starters.
3. Make sure all connections are in accordance with the National Electrical Code and any local regulations.
4. To reduce the risk of electric shock, disconnect both normal and emergency power supplies and inverter connector of the emergency
4. To reduce the risk of electric shock, disconnect both normal and emergency power supplies and inverter connector of the emergency
ballast before servicing.
5. This emergency ballast is for factory or field installation in either the ballast channel or on top of the fixture.
6. This product is for use in indoor fixtures except air handling heated air outlets, and wet, damp, or hazardous locations.
7. An unswitched AC power source is required (120 or 277 VAC, 60Hz).
8. Do not install near gas or electric heaters.
9. Do not attempt to service the battery. A sealed, no-maintenance battery is used that is not field replaceable. Contact the
6. This product is for use in indoor fixtures except air handling heated air outlets, and wet, damp, or hazardous locations.
7. An unswitched AC power source is required (120 or 277 VAC, 60Hz).
8. Do not install near gas or electric heaters.
9. Do not attempt to service the battery. A sealed, no-maintenance battery is used that is not field replaceable. Contact the
manufacturer for information on service.
10. The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition.
11. Do not use this product for other than intended use.
12. Servicing should be performed by qualified service personnel.
11. Do not use this product for other than intended use.
12. Servicing should be performed by qualified service personnel.
B50FEB
net
Ni-Cd
! IMPORTANT SAFEGUARDS !
05/18/05
FCC COMPLIANCE STATEMENT
1.
WARNING:
The antenna used for this device must be installed to provide a separation distance of at least 20cm (8 inches) from all
persons, and must not be co-located or operating in conjunction with any other antenna or transmitter other than those
contained within this device.
contained within this device.
2.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate
the equipment.
the equipment.
3.
This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which is found by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which is found by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna
•
Increase the separation between the equipment or devices
•
Connect the equipment to an outlet other than the receiver’s
•
Consult a dealer or an experienced radio/TV technician for assistance