Wilson Electronics LLC 2B2725 用户手册

Wilson Electronics, Inc. has been a leader in the wireless communications industry for over 40 years. 

The company designs and manufactures Signal Boosters, antennas and related components that 

significantly improve cellular phone signal reception and transmission in a wide variety of applications, 

both mobile (marine, RV, vehicles) and in-building (home, office, M2M).

With extensive experience in antenna and Signal Booster research and design, the company’s 

engineering team uses a state-of-the-art testing laboratory, including an anechoic chamber and network 

analyzers, to fine-tune antenna designs and performance. For its Signal Boosters, Wilson Electronics 

uses a double electrically shielded RF enclosure and cell tower simulators for compliance testing.

Wilson Electronics Signal Boosters feature patented Smart Technology   ™ that enables them to 

automatically adjust their power based on cell tower requirements.  By detecting and preventing 

oscillation (feedback), signal overload and interference with other users, these Smart Technology   ™ 

Signal Boosters improve network cell phone areas without compromising carrier systems.

All products are engineered and assembled in the company’s 55,000-square-foot headquarters in St. 

George, Utah. Wilson Electronics has product dealers in all 50 states as well as in countries around the 

world.

Warning: 

Do not plug in the power supply until the Outside Antenna cable is attached to the Sleek.

Warning: 

RF Safety: The Sleek cradle/Signal Booster must be installed with a separation of at least 8 inches  

 

from all persons and must not be located in conjunction with any other antenna or Signal Booster.

Warning: 

RF Safety: The FCC requires that a cell phone with cradle attached may only be used 

 

with the cradle mounted as illustrated in this installation guide. A cell phone held near the   

 

ear must be without the cradle attached.

Warning: 

RF Safety: All Inside Antennas used with this Signal Booster may not have gain (less cable loss)  

 

that exceeds 15 dBi and must be located at least 8 inches from all people. Outside antennas may  

 

not have gain (less cable loss) that exceeds 3.4 dBi and must be located at least 8 inches from all  

 

people. All antennas shown on page one meet these requirements.

Warning:

DO NOT use phone covers that have chrome or any other metallic surface. It may block cellular signals.

All Wilson Electronics products are protected by Wilson Electronics 30-day money-back guarantee.  If, for any reason, the performance of any product is not acceptable, simply 

return the product directly to the reseller with a dated proof of purchase.

Wilson Electronics Signal Boosters are warranted for one (1) year against defects in workmanship and/or materials.  Warranty issues may be resolved by returning the 

product directly to the reseller with a dated proof of purchase.  
Signal Boosters may also be returned directly to the manufacturer at the consumer’s expense, with a dated proof of purchase and a Returned Material Authorization (RMA) 

number supplied by Wilson Electronics.  Wilson Electronics shall, at its option, either repair or replace the product. Wilson Electronics will pay for delivery of the repaired or 

replaced product back to the original consumer within the continental United States.  
This warranty does not apply to any Signal Boosters determined by Wilson Electronics to have been subjected to misuse, abuse, neglect, or mishandling that alters 

or damages physical or electronic properties.
Failure to use a surge protected AC Power Strip with at least a 1000 Joule rating will void your warranty.
RMA numbers may be obtained by contacting Technical Support at 866-294-1660.  

Disclaimer:   The information provided by Wilson Electronics, Inc. is believed to be complete and accurate.  However, no responsibility is assumed by Wilson Electronics, Inc. 

for any business or personal losses arising from its use, or for any infringements of patents or other rights of third parties that may result from its use.

Copyright © 2012 Wilson Electronics, Inc.  All rights reserved.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) this device 

must accept any interference received, including interference that may cause undesired operation. Changes or modifications made that are not expressly approved by Wilson 

Electronics could void authority to operate this equipment.