Lumenetix Inc LCT001 用户手册
Copy and Paste
Copy and Paste Cont.
Copy and Paste Cont.
Calibration
Dimming
Federal Communication Commission
Interference Statement
Copy a Lumenetix Lamp
• Use the Gray Card
included in the Light
Commissioning Tool
Commissioning Tool
• Hold the Gray Card in the
center of the beam of the lamp
to be copied. The ideal distance
from the lamp is 4 feet (120 cm)
to be copied. The ideal distance
from the lamp is 4 feet (120 cm)
• Aim the light commissioning tool at the center
of the Gray Card
• Press and hold COPY for two seconds.
The Display will read “Copy”
Select the Target Lamp
• Press the TARGET button
• The active lamp will blink green
• To target a different lamp in the wireless network,
continue to press TARGET until the desired lamp
blinks green
blinks green
For assistance with the operation
of the Light Commissioning Tool,
of the Light Commissioning Tool,
please visit www.lumenetix.com
Instruction Manual
Light Commissioning Tool
Model Number LCT Zero
Lamp On and Off
Select a Lamp
Introduction
Inserting the Batteries
Network Scan
3 x AAA
• Remove the battery case on the back of the
remote control by pushing the tab in and sliding
the cover down
the cover down
• Insert 3 AAA batteries ensuring that the positive
and negative terminals are correctly matched
• Replace the battery case
SCAN
SELECT
COPY
TARGET
CALIBR A TION
PASTE
SCAN / SELECT
POWER
BRIGHTNESS UP
CCT UP
CCT DOWN
DISPLAY
PASTE
BRIGHTNESS DOWN
COPY
TARGET
REMOTE CONTROL
Scan the Wireless Network
to Discover Lamps
• Aim the remote control at the lamp(s)
to Discover Lamps
• Aim the remote control at the lamp(s)
and press and hold SELECT until the display
indicates that the light commissioning tool is
scanning the network to discover all lamps
indicates that the light commissioning tool is
scanning the network to discover all lamps
• After a few seconds, the active lamp will flash
• The display indicates the quantity of lamps
discovered on the network
Light Commissioning Tool Functions
• Wirelessly controls araya lamp power on/off,
brightness, and color temperature
• Copy and Paste – copy a Lumenetix lamp and
paste it onto a Lumenetix lamp
• Calibration – Compensates for different LED
aging characteristics
• The active lamp in the network flashes in
Network Scan
• To access another lamp in the network, press
SELECT again. The next lamp in the network
will flash.
will flash.
• Continue to press SELECT until the desired
lamp flashes
• The display will update to indicate the lamp
within the network
SELECT
SCAN
SELECT
SELECT
COPY
TARGET
CALIBRATION
PASTE
SCAN
SELECT
SELECT
SCAN
SCAN
SELECT
SELECT
COPY
TARGET
CALIBRATION
PASTE
SELECT
SCAN
SELECT
SELECT
LAMP ON / OFF
HOLD 2 SEC
CCT 3000K
DIM 100%
SCAN
SELECT
SELECT
SCAN
SELECT
SELECT
COPY
TARGET
CALIBR A TION
PASTE
LAMP ON / OFF
CCT 3000K
DIM 100%
SCAN
SELECT
SELECT
SCAN
SELECT
SELECT
Increasing the Brightness
• The brightness can be
adjusted from 5% to 100% in increments of 1%
• Press the brightness UP key to increase the brightness
• The selected dimming level is shown in the display
Decreasing the Brightness
• The lamp can be dimmed from 100% to 5% in
increments of 1%
• Press the brightness DOWN key to dim the lights
• The selected dimming level is shown in the display
Adjusting Color Temperature (CCT)
Increasing the Color
Temperature
Temperature
• The color temperature
can be adjusted from
2700K to 4200K in
increments of 100K
2700K to 4200K in
increments of 100K
• Press the CCT UP key
to increase the color temperature
• The selected color temperature is shown in the display
Decreasing the Color Temperature
• The color temperature can be adjusted from 4200K
to 2700K in increments of 100K
• Press the Color Temperature DOWN key to decrease
the color temperature
• The selected color temperature is shown in the display
SELECT
SCAN
SELECT
SELECT
COPY
TARGET
CALIBRATION
PASTE
COPY
HOLD 2 SEC
COPY
TARGET
CALIBR A TION
PASTE
TARGET
SCAN
SELECT
SELECT
Paste
• Use the Gray Card included in the Light
• Use the Gray Card included in the Light
Commissioning Tool
• Hold the Gray Card in the center of the beam
of the lamp to be pasted. The ideal distance
from the lamp is 4 feet (120 cm)
from the lamp is 4 feet (120 cm)
The distance that the gray card was held from
the lamp that was copied should be equal to
the distance that the gray card is held from
the lamp to be pasted
• Aim the light commissioning tool at the center
of the Gray Card
• Press and hold PASTE for two seconds.
The Display will read “Paste”
• Keep the Light Commissioning Tool steadily
pointed at the Gray Card until the lamp flashes
twice, indicating that the operation is complete
twice, indicating that the operation is complete
• The brightness and color temperature will be
shown in the display
COPY
TARGET
CALIBRATION
PASTE
PASTE
SCAN
SELECT
SELECT
HOLD 2 SEC
CALIBRATION
COPY
TARGET
CALIBR A TION
PASTE
SCAN
SELECT
SELECT
• Press the SELECT button to access the active lamp
in the network
• The active lamp will flash
• To access other lamps in the wireless network,
continue to press SELECT until the desired lamp
blinks amber
blinks amber
• Simultaneously press the COPY and PASTE buttons
• The lamp will begin calibration of the LEDs
• Upon completion the lamp will flash twice
• Press the POWER button and the selected lamp
will turn on
• The brightness and color temperature will be
shown in the display
• To turn the lamp off, press the POWER button
• If the lamp does not light, check the dimming
level and adjust to the desired brightness (see
next page)
next page)
BRIGHTNESS UP
BRIGHTNESS DOWN
COPY
TARGET
CALIBRATION
PASTE
SCAN
SELECT
SELECT
Selecting the Lamp to Copy
• Using the SCAN SELECT
button, select the light to be copied
• The active lamp will flash
• To access another lamp in the wireless
network, press SELECT again (the next lamp
in the network will flash)
in the network will flash)
• Continue to press SELECT until the desired
lamp flashes
CCT UP
CCT DOWN
COPY
TARGET
CALIBRATION
PASTE
SCAN
SELECT
SELECT
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate
this equipment.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate
this equipment.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
FCC ID: Q8A-LCT001