Budderfly LLC S0711011 用户手册
Part No S0711011
Description:
Installing a Budderfly adapter transforms your building’s existing wiring into the “Budderfly Open Network” and allows the adapter to
monitor energy consumption and communicate the data to a facility controller.
Budderfly adaptors will use the existing power line for communication and thus require no re‐wiring.
Using our Budderfly software, you can visualize consumption data and manage each individual adapter.
The Budderfly lighting switch is a component of the Budderfly system and designed to work with all other Budderfly devices. It is a
plug‐and‐play replacement for your existing lighting switch. Once installed, the Budderfly switches also act as repeaters to extend the
range of the network and increase efficiency.
monitor energy consumption and communicate the data to a facility controller.
Budderfly adaptors will use the existing power line for communication and thus require no re‐wiring.
Using our Budderfly software, you can visualize consumption data and manage each individual adapter.
The Budderfly lighting switch is a component of the Budderfly system and designed to work with all other Budderfly devices. It is a
plug‐and‐play replacement for your existing lighting switch. Once installed, the Budderfly switches also act as repeaters to extend the
range of the network and increase efficiency.
This device is designed for use only with permanently installed fixtures.
Installation:
The Budderfly switch may be used in new installations or to replace an existing wall switch. It is intended to be used only as a 2‐way switch. The wiring schematic will be as per below:
1. At the circuit breaker or fuse panel, disconnect the power for all of the circuits in
the switch junction box..
2. Double Check that the power is OFF to the switch box before continuing by trying
to turn on the controlled load.
3. Remove the wall plate from the switch you are replacing. Then, unscrew the switch
itself and pull it out from the junction box.
4. Disconnect the wires from the switch you are replacing.
5. Follow the Wiring information provided below to connect the wires as follows:
5. Follow the Wiring information provided below to connect the wires as follows:
o
Connect the GROUND wire (usually Bare Copper or Green) to the Ground wire of
Budderfly Switch (Yellow & Green).
Budderfly Switch (Yellow & Green).
o
Connect the LOAD wire (usually Black) that goes to the light to the LOAD wire of
Budderfly Switch (Red).
Budderfly Switch (Red).
o
Connect the LINE wire (usually Black) that comes from the electrical service panel
to the HOT wire of Budderfly Switch (Black).
to the HOT wire of Budderfly Switch (Black).
o
Connect the NEUTRAL wire (usually White) to the Neutral wire of Budderfly
Switch (White).
Switch (White).
6. After you have connected all of the wires, ensure that all of the wire connectors
are firmly attached and that there is no exposed copper except for the GROUND
wire.
wire.
7. Gently place Budderfly switch into the junction box, orienting the unit with the LED
bar on the left. Then, screw the switch into place.
8. Reinstall the wall plate
9. Enable power to the switch from the circuit breaker or fuse panel
9. Enable power to the switch from the circuit breaker or fuse panel
10. After the Power LED comes on, test that the switch is working properly by turning
the light on and off
11. Add the device address to the Budderfly web application.
WARNING –ELECTRICAL SHOCK HAZARD
• The Budderfly Dual Band Light Switch is intended for installation in accordance with the National Electric
Code and local regulations in the United States.
• If you are not knowledgeable or comfortable with electrical circuitry, you should have a qualified electrician
install the Budderfly Dual Band Light Switch for you.
Warning
RISK OF FIRE / ELECTRICAL SHOCK / BURNS
Exercise extreme caution when using Budderfly switching devices to control appliances.
To avoid the risk of Fire, Electrical Shock, Burns or other hazards we recommend the following:
Exercise extreme caution when using Budderfly switching devices to control appliances.
To avoid the risk of Fire, Electrical Shock, Burns or other hazards we recommend the following:
• Install the Budderfly switches indoor only.
• Never use the Budderly switches to control medical and/or life support equipment.
• Do not use the Budderfly switches to control electric heaters or any other appliances which may present a
• Never use the Budderly switches to control medical and/or life support equipment.
• Do not use the Budderfly switches to control electric heaters or any other appliances which may present a
hazardous condition due to unattended or unintentional power on control.
Never use the Budderfly switches with loads that exceed the maximum rating specified.
WARNING –ELECTRICAL SHOCK HAZARD
• Turn OFF the power to the branch circuit for the switch and lighting fixture at
the service panel.
• All wiring connections must be made with the POWER OFF to avoid personal
injury and/or damage to the switch.
Wiring Information
• Important: Budderfly Switch is rated for and intended to only be used with
copper wire.
• Use 12 AWG or larger wires suitable for 80
o.
• Remove 3/4" (1.9 cm) of insulation from each wire.
•
Connect as follows: Twist strands of each end tightly together. Hold bare
ends of wires together and push firmly into wire Nut. Screw Nut clockwise
making sure that no bare conductor shows below the connector.
ends of wires together and push firmly into wire Nut. Screw Nut clockwise
making sure that no bare conductor shows below the connector.
WARNING: If you are not sure
about any part of the above
instructions, consult a qualified
electrician.
about any part of the above
instructions, consult a qualified
electrician.